AXE XCaliber Taper Tip Graphite Iron Shaft Set

AXE XCaliber Taper Tip Graphite Iron Shaft Set

XCaliber R Flex - .355", Taper Tip Set (39"-36") (75g) 3B2H
In Stock
XCaliber S Flex - .355", Taper Tip Set (39"-36") - (85g) 4B2H
In Stock
1-3 $15.50
4+ $13.50
Tip & Butt Trimming
Tip Prepping

AXE XCaliber Taper Tip Graphite Iron Shaft Set

The Arthur Xtreme Engineering Xcaliber graphite iron shaft features Zone Stiffness Technology (ZST) which helps golf shots get airborne without excessive spin.

  • .355" taper tip diameter
  • Lowest balance point of any iron in the industry combined with a med/stiff lower section helps get shots airborne without excessive spin
  • At 15 cpm stiffer than the XCaliber Hybrid, easy to make a progressively stiffer set of clubs

Individual AXE XCaliber Iron Shafts can be purchased here

Trimming Instructions

Arthur Xtreme Engineering Xcaliber Graphite Iron Shaft Specifications

AXE XCaliber Taper Tip Graphite Iron Shaft Set is rated 5.0 out of 5 by 7.
Rated 5 out of 5 by from Great graphite taper tip shafts Excellent set of taper tip shafts for forged irons. Perfect balance, good trajectory and they look great. A fantastic way of extending the life of many older forged iron sets. Highly recommended.
Date published: 2014-08-17
Rated 5 out of 5 by from Excellent Shafts Bought them to replace my steelfiber shafts as I didn't like the boardy feel and left shoulder was suffering from the heavy weights. So far these shafts are really smooth and feel a lot more lively, could be due to the light weights allowing me to feel the club head more. Initially I was going to get the stiff flex since I was scared in the huge weight gap, but Arthur was very helpful in assuring me that the R flex was a good fit for me. For the price, it's really an underrated product.
Date published: 2016-04-08
Rated 5 out of 5 by from Nice feeling shaft I bought a set of these about 3 weeks ago to put in my Ping I-25 irons. They have a great feel and have a mid to mid high kick point. I replaced the Ping steel shafts with these. Still dialing them in a bit as I made them about 3/8 of an inch longer and had to bend the lie angle a little flatter to compensate for the increased length. No vibration with them.
Date published: 2016-05-06
Rated 5 out of 5 by from delivers on distance I had a hard time swingweighting these, today I hit them at the range. they delivered as promised, high and far, great feel, not harsh. mid irons 7 yrds further, wedges 10 yard further and long irons 5 yard further than my xp90's but with more dispersion
Date published: 2016-05-06
Rated 5 out of 5 by from Nice paint job I don't think I'm going to put him in a set of Forge golf clubs maybe a perimeter wait, like a tailor-made but then they just go to far and there's just no telling which way it's going to be so maybe I could try am in a forge club
Date published: 2016-09-15
Rated 5 out of 5 by from Economically Efficiency Installed as upgrade from steel for player seeking more distance and reports indicate great acceptance by player. Seeing great performance at a very reasonable price.
Date published: 2016-04-29
Rated 5 out of 5 by from Very consistent ..... Good weight.. One of few taper tip irons shafts available at a decent, reasonable price.
Date published: 2015-10-25
  • y_2016, m_12, d_7, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_AS0028S, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

Can I use these shafts to replace my steel shafts in a set of Ping Black Dot GMax irons? They now have Ping CFS SR Steel Distance shafts. Also, is there a guide for tip and butt length trims?

Asked by: gbarn
Yes the AS0028 shafts will fit the Ping GMax irons. With these taper tip shaft there is no tip trimming. You will install them and butt cut them to your finished length. Here is a link to our standard length reference. Quite a few of these shafts are on backorder and are not due in until the middle of January 2017.
Answered by: JimY
Date published: 2016-11-21

What shafts would complement for use in 2 and 3 iron since these start at 4?

Asked by: 4golfgod
To be honest there really is not a very good match especially for a 2 iron because there are only a few taper tip graphite 2 iron shafts available. The UST Recoil 95/110/125 come with a 2 iron shaft. Also the Paderson Kinetixx IMRT Kevlar 950 Iron comes with a 2 iron shaft. Those are the only ones we stock in a 2 iron shaft and their specifications do not match up to this Xcaliber shaft. If you are using an R flex a shaft like the UST Recoil 670 (US0072) or for the S flex the Recoil 680 (US0072) could match up better. These are a stock .370" tip diameter but could be special ordered from UST with a .355" taper tip and set up for the 2 and 3 irons. You would need to contact our Customer Service Department for this special order. You can contact them at or by calling 1-800-848-8358.
Answered by: JimY
Date published: 2016-11-03

I have a set of Mizuno MX 900 irons with steel Gold Dynamic I've gotten older I would prefer a graphite shaft..will these shafts compliment this set of irons..I have the 3 thru PW...If the set comes with 7 shafts what do you suggest for the 3

Asked by: TKeen
The Xcaliber taper tip iron shafts could match well with the MX 900 Mizuno irons. I know we are currently out of stock on some of the Xcaliber taper tip shafts and we will not be getting them in stock until the first part of December. I know it shows we have the sets in stock but if we do not have the individual shafts in stock the sets would not be in stock. We simply pull the individual shafts when a set order comes in.
Answered by: JimY
Date published: 2016-10-24

I have a set of ping zing 2, red dot (1* flat) 3-sw, ls, lw with steel jz shafts that i hit a little high. Considering reshafting with the .355 xcaliber graphite shaft. Can i cut down the 39" regular shaft to place it in the 5 and so on down the line?

Asked by: Jason
The 39" raw length shaft is actually the 4 iron shaft. Xcaliber does not offer a 3 iron shaft with these taper tip shafts. You could start with the 4 iron shaft into the 3 iron and you would have to use the 36" shaft in the 9 iron and wedges. This will make the shafts play approximately a quarter to half a flex stiffer then their listed flex.
Answered by: JimY
Date published: 2016-10-17

 How many is in a set 

Asked by: Johnrap
You will get 7 shafts if you buy the set.
Answered by: Brent Dill
Date published: 2016-08-24

Can I have this shafts installed on Callaways Diablo forged iron heads? Mahalo's

Asked by: George
The information that I have lists the Diablo Forged irons as a .370" parallel tip shaft which would be the AS0023 Xcaliber Iron shafts.
Answered by: JimY
Date published: 2016-08-04

I need to re-shaft 4-Utility Wedge (8 clubs). Will this set of AXE XCaliber Taper Tip Graphite Iron Shaft Set the correct number and the correct shafts for my Ping I20 irons?

Asked by: Jim
The set of 8 Xcaliber taper tip shafts are for a 4 through PW. The PW shaft could be used for PW, Gap Wedge, Sand Wedge or Lob Wedge or Utility Wedge.
Answered by: JimY
Date published: 2016-07-06

I need to confirm that these will fit into a combo set of Hogan Apex Edge Pro/Apex 50 irons.

Asked by: 9iron2
Yes the Hogan irons would be a .355" taper tip and these shafts will fit.
Answered by: JimY
Date published: 2016-07-05
  • 2016-12-07T08:34CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_36
  • loc_en_US, sid_AS0028S, PRD, sort_recentAnswersFirst
  • clientName_golfworks