AXE XCaliber Taper Tip Graphite Iron Shaft Set

AXE XCaliber Taper Tip Graphite Iron Shaft Set

XCaliber R Flex - .355", Taper Tip Set (39"-36") (75g) 3B2H
In Stock
XCaliber S Flex - .355", Taper Tip Set (39"-36") - (85g) 4B2H
In Stock
1-3 $15.50
4+ $13.50
Tip & Butt Trimming
Tip Prepping

AXE XCaliber Taper Tip Graphite Iron Shaft Set

The Arthur Xtreme Engineering Xcaliber graphite iron shaft features Zone Stiffness Technology (ZST) which helps golf shots get airborne without excessive spin.

  • .355" taper tip diameter
  • Lowest balance point of any iron in the industry combined with a med/stiff lower section helps get shots airborne without excessive spin
  • At 15 cpm stiffer than the XCaliber Hybrid, easy to make a progressively stiffer set of clubs

Individual AXE XCaliber Iron Shafts can be purchased here

Trimming Instructions

Arthur Xtreme Engineering Xcaliber Graphite Iron Shaft Specifications

AXE XCaliber Taper Tip Graphite Iron Shaft Set is rated 5.0 out of 5 by 7.
Rated 5 out of 5 by from Great graphite taper tip shafts Excellent set of taper tip shafts for forged irons. Perfect balance, good trajectory and they look great. A fantastic way of extending the life of many older forged iron sets. Highly recommended.
Date published: 2014-08-17
Rated 5 out of 5 by from Excellent Shafts Bought them to replace my steelfiber shafts as I didn't like the boardy feel and left shoulder was suffering from the heavy weights. So far these shafts are really smooth and feel a lot more lively, could be due to the light weights allowing me to feel the club head more. Initially I was going to get the stiff flex since I was scared in the huge weight gap, but Arthur was very helpful in assuring me that the R flex was a good fit for me. For the price, it's really an underrated product.
Date published: 2016-04-08
Rated 5 out of 5 by from Nice feeling shaft I bought a set of these about 3 weeks ago to put in my Ping I-25 irons. They have a great feel and have a mid to mid high kick point. I replaced the Ping steel shafts with these. Still dialing them in a bit as I made them about 3/8 of an inch longer and had to bend the lie angle a little flatter to compensate for the increased length. No vibration with them.
Date published: 2016-05-06
Rated 5 out of 5 by from delivers on distance I had a hard time swingweighting these, today I hit them at the range. they delivered as promised, high and far, great feel, not harsh. mid irons 7 yrds further, wedges 10 yard further and long irons 5 yard further than my xp90's but with more dispersion
Date published: 2016-05-06
Rated 5 out of 5 by from Nice paint job I don't think I'm going to put him in a set of Forge golf clubs maybe a perimeter wait, like a tailor-made but then they just go to far and there's just no telling which way it's going to be so maybe I could try am in a forge club
Date published: 2016-09-15
Rated 5 out of 5 by from Economically Efficiency Installed as upgrade from steel for player seeking more distance and reports indicate great acceptance by player. Seeing great performance at a very reasonable price.
Date published: 2016-04-29
Rated 5 out of 5 by from Very consistent ..... Good weight.. One of few taper tip irons shafts available at a decent, reasonable price.
Date published: 2015-10-25
  • 2016-10-27T07:56CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_AS0028S, PRD, sort_relevancy
  • clientName_golfworks

I have a set of Mizuno MX 900 irons with steel Gold Dynamic I've gotten older I would prefer a graphite shaft..will these shafts compliment this set of irons..I have the 3 thru PW...If the set comes with 7 shafts what do you suggest for the 3

Asked by: TKeen
The Xcaliber taper tip iron shafts could match well with the MX 900 Mizuno irons. I know we are currently out of stock on some of the Xcaliber taper tip shafts and we will not be getting them in stock until the first part of December. I know it shows we have the sets in stock but if we do not have the individual shafts in stock the sets would not be in stock. We simply pull the individual shafts when a set order comes in.
Answered by: JimY
Date published: 2016-10-24

I have a set of ping zing 2, red dot (1* flat) 3-sw, ls, lw with steel jz shafts that i hit a little high. Considering reshafting with the .355 xcaliber graphite shaft. Can i cut down the 39" regular shaft to place it in the 5 and so on down the line?

Asked by: Jason
The 39" raw length shaft is actually the 4 iron shaft. Xcaliber does not offer a 3 iron shaft with these taper tip shafts. You could start with the 4 iron shaft into the 3 iron and you would have to use the 36" shaft in the 9 iron and wedges. This will make the shafts play approximately a quarter to half a flex stiffer then their listed flex.
Answered by: JimY
Date published: 2016-10-17

 How many is in a set 

Asked by: Johnrap
You will get 7 shafts if you buy the set.
Answered by: Brent Dill
Date published: 2016-08-24

Can I have this shafts installed on Callaways Diablo forged iron heads? Mahalo's

Asked by: George
The information that I have lists the Diablo Forged irons as a .370" parallel tip shaft which would be the AS0023 Xcaliber Iron shafts.
Answered by: JimY
Date published: 2016-08-04

I need to re-shaft 4-Utility Wedge (8 clubs). Will this set of AXE XCaliber Taper Tip Graphite Iron Shaft Set the correct number and the correct shafts for my Ping I20 irons?

Asked by: Jim
The set of 8 Xcaliber taper tip shafts are for a 4 through PW. The PW shaft could be used for PW, Gap Wedge, Sand Wedge or Lob Wedge or Utility Wedge.
Answered by: JimY
Date published: 2016-07-06

I need to confirm that these will fit into a combo set of Hogan Apex Edge Pro/Apex 50 irons.

Asked by: 9iron2
Yes the Hogan irons would be a .355" taper tip and these shafts will fit.
Answered by: JimY
Date published: 2016-07-05

I have a set of Ping I 3 O size clubs and was wondering if I would need a shaft for my Sand wedge with this set?

Asked by: Cal
You certainly could install one of these shafts into the sandwedge. A lot of players choose to use steel shafts in their sandwedge but it becomes a preference as to which one would work best for you. With the Xcaliber graphite shaft you would use the 36" raw length shaft for the SW.
Answered by: JimY
Date published: 2016-06-24

Can I install this shafts into my Callaway Diablo forged irons? What lenght shaft you recommend for the PW ?

Asked by: George
Actually the Diablo Forged irons used a .370" parallel tip shaft. You would use the AS0023 shaft for these irons. You still could use the Xcaliber taper tip AS0028S but you would need to shim them to make them fit. The 36" raw length shaft is the shaft for the PW and any other wedges.
Answered by: JimY
Date published: 2016-06-24
  • 2016-10-27T07:51CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_34
  • loc_en_US, sid_AS0028S, PRD, sort_recentAnswersFirst
  • clientName_golfworks