Club-Conex Faz-Fit Fitting Adaptors

Club-Conex Faz-Fit Fitting Adaptors


Faz-Fit Hosel Adaptor - .335"
$11.99
In Stock
Faz-Fit Hosel Adaptor - .350"
$11.99
In Stock
Faz-Fit Hosel Adaptor - .370"
$11.99
In Stock
Faz-Fit Titanium Shaft Adaptor - .335"
$14.99
In Stock
Faz-Fit Titanium Shaft Adaptor - .350"
$14.99
In Stock
Faz-Fit Titanium Shaft Adaptor - .370"
$14.99
In Stock
Faz-Fit Assembly Wrench
$10.99
In Stock
Faz-Fit Installation Tool - Iron
$7.99
In Stock
Faz-Fit Installation Tool - Wood
$7.99
In Stock

Club-Conex Faz-Fit Fitting Adaptors

The Faz-Fit is the finest adapter system available for metal wood fitting and demonstration purposes. Faz-Fit adaptors, designed for club fitting professionals, can be installed into just about any type of club head or shaft in just a few easy steps. Just imagine, with only (10) club heads and (10) shafts utilizing Faz-Fit interchangeable adaptors you will have the equivalent of one hundred different club configurations. Works for both RH and LH club heads. The Faz-Fit 2010 features a completely new taper profile and an anti-rotational tip section that is more durable and 25% lighter than the original Faz-Fit adaptors.

  • The original Faz-Fit and the Faz-Fit 2010 metal wood adaptors are completely compatible with each other and can be interchanged
AccessDeniedAccess Denied39848EFC9CC01791l6Pl8D35pnJsiBn/VmnnY9qgp3bxFRazdFPyGZGZVOItfNGuZcdOpKyMh1P+fbHq4wWGXftowYc=

Can this system be used to convert a Callaway 11 degree ERC driver to 13 degrees?

Asked by: Efstwo
No. This Faz-Fit adapter just allows you to change from one shaft to another. It makes not adjustments. The Face-Fit adapter will change face angle which will effectively change loft. If you close the face angle by 1.5 degrees, which this adapter allows you to change, you will effectively increase the loft by 1.5 degrees. So it would make 11 degrees play like 12.5 degrees, but also have a closed face angle. http://www.golfworks.com/club-conex-face-fit-adaptor-system/p/CC0021/
Answered by: JimY
Date published: 2016-07-05

can you use the .370 shaft adapter with a .355 shaft ?

Asked by: scratch hacker
After trimming for flex, i've had success using the .370 on a .355 with most shafts. Using a little bit of quick center has been helpful in the rare cases. No issues thus far with heads flying off, etc - about 1 year of pretty hard use. The shafts have just enough taper to be OK when the tip length is cut. Definitelly not recommended by the manufacturer though.
Answered by: Chris
Date published: 2016-07-01

Can this system or another system be used to universally fit the taper tip iron heads and shafts as well?

Asked by: clubbuilder115
I have used this system effectively on Both taper tip and .370 shafts.  With the trimming that needs to be done, it works out. If you're using the hosel insert on a Taper, the manufacturer suggests boring out the hosel ID to fit. I have had success with sanding the hosel adapter to fit, but it is not recommended by the Manufacturer. 
Answered by: Chris
Date published: 2016-04-19

with this Faz fit can try several shafts on the same driver head?

Asked by: DeeC
If you install the hosel sleeve, then you can install the shaft sleeves on multiple shafts and use all in that driver head.
Answered by: GW2002
Date published: 2015-02-02

Is it possible to install this adapter into any driver head och shaft? Do i need any tool to install it or epoxy. Is it then possible to shift shaft easily to the same head?

Asked by: Janne
  • 2016-09-26T07:53CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_5
  • loc_en_US, sid_CC0025, PRD, sort_recentAnswersFirst
  • clientName_golfworks