Golf Club Iron Ferrules - Black

Golf Club Iron Ferrules - Black


59PI Dozen - Black Short .370" Iron Ferrules
$2.49
In Stock
59PI Single - Black Short .370" Iron Ferrule
$0.35
In Stock
60PI Dozen - Black Std .370" Iron Ferrules
$2.49
In Stock
60PI Single - Black Std .370" Iron Ferrule
$0.35
In Stock
74PI Dozen - Black Long .370" Iron Ferrules
$2.49
In Stock
74PI Single - Black Long .370" Iron Ferrule
$0.35
In Stock
61PI Dozen - Black X-Long .370" Iron Ferrules
$2.49
In Stock
61PI Single - Black X-Long .370" Iron Ferrule
$0.35
In Stock
Dozen Rubber O-Rings
$2.25
In Stock

Golf Club Iron Ferrules - Black

HUGE GOLF FERRULE SELECTION!

A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!

Golf Club Iron Ferrules - Black is rated 4.0 out of 5 by 1.
Rated 4 out of 5 by from 60PI 0.370" Iron Ferrules Purchased these so I could reshaft a 0.370" parallel tip hybrid. They fit very tight onto a 0.370" parallel tip shaft so make sure you have a tool to install them or you will get frustrated or damage your shaft. I drilled a 3/8" hole in a 1" block of wood and used that to get the ferrule started and then finished the insertion by placing the club head on the shaft and hitting down on it until the shaft was fully seated into the club (~1.5"). Be sure to have your tip weights installed first as once these ferrules are on, they can only be removed by cutting them off - I've had to do that before. These could be made a little looser to make the install easier. Otherwise they look good and are exact to sizing. They work much better for 0.355" taper tips.
Date published: 2015-11-05
  • 2016-09-29T07:56CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_60PI, PRD, sort_relevancy
  • clientName_golfworks

What ferrule would I need for a 2012 Mizuno JPX EZ iron?

Asked by: Jaylam003
The 61PI would work well and match in length to what Mizuno used. There is a chance that Mizuno uses a collared ferrule in which case the BB0001 collared ferrule would work. Either one can work.
Answered by: JimY
Date published: 2016-07-20

Proper ferrule for Srixon irons

Asked by: Thibs
Srixon irons use a .355" taper tip shaft but you can use a .370" ferrule because the .355" taper tip shaft will taper out to approximately .370" where the shaft exits the top of the hosel. The Srixon irons probably use a collared ferrule and our BB0001 would probably work well. http://www.golfworks.com/collared-golf-club-ferrules/p/BB0001/
Answered by: JimY
Date published: 2016-07-18

What size ferrules (model #) to use with 96/97 Callaway Big Bertha Irons (original graphite shafts)?

Asked by: silk
We would use the BB9003 ferrules for these irons. http://www.golfworks.com/callaway-collared-iron-ferrule-370/p/BB9003/
Answered by: JimY
Date published: 2016-06-30

I want to reshaft my adams idea black cb3 irons with dynamic gold x100 shafts. Which ferrule would work best for this?

Asked by: Zack
In looking at pictures of the CB3 Black irons Adams used a ferrule with a single Chrome ring like the 52PI. Any .370" ferrule will work whether it is plain black or with trim rings.
Answered by: JimY
Date published: 2016-06-27

I am reshafting a set of Cobra Amp Cell irons with .355 taper tip shafts so I know I need a .355 ferrule.  Do I need a collared ferrule and if so which one?

Asked by: Pakman
I am quite sure the AMP Cell irons use a collared ferrule. We do not stock a collared ferrule for .355" taper tip shafts but you can use a .370" ferrule with .355" taper tip shafts. .355" taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel so the .370" ferrules will fit. The BB0008 collared ferrule should work fine and match to what Cobra used. http://www.golfworks.ca/collared-golf-club-ferrules/p/BB0001/
Answered by: JimY
Date published: 2016-06-08

Would like to match Taylormade RSI 2 Ferrule, what part number should I order?

Asked by: Joe
In looking at pictures of the RSI 2 irons I see a plain black ferrule like our 61PI. However you could use any .370" ferrule that you would like. http://www.golfworks.com/golf-club-iron-ferrules-black/p/60PI/
Answered by: JimY
Date published: 2016-05-25

I can not find 68WIR in your online order section - how do I order this?

Asked by: KMack
They show up at this link. I will see about getting them listed on the other link as well. http://www.golfworks.com/rubber-o-ring-ferrules/p/68WIRS/
Answered by: JimY
Date published: 2016-05-17

I need a replacement ferrules for my Titleist 714 CB .355" and .370" .. What size do you recommend? Is it the same as original Titleist ferrules? May I know what is the shipping cost to malaysia for 1 dozen of .355" and 1 dosen of .370"?Thank you.

Asked by: Zarith
I would use the 61PI. It will work for both the .355" and .370" shafts. A .355" taper tip shaft has tapered out to approximately .370" where the shaft exits the top of the hosel so the .370" ferrule will fit. As for shipping costs to Malaysia you will need to contact our Customer Service Department at golfworks@golfworks.com.
Answered by: JimY
Date published: 2016-04-29
  • 2016-09-29T08:05CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_28
  • loc_en_US, sid_60PI, PRD, sort_recentAnswersFirst
  • clientName_golfworks