Golf Club Wood Ferrules - Black

Golf Club Wood Ferrules - Black


59PW - Blk Short .335" (Dozen)
$2.49
In Stock
59PW - Blk Short .335" (Single)
$0.35
In Stock
60PW - Blk Std .335" (Dozen)
$2.49
In Stock
60PW - Black Std .335" (Single)
$0.35
In Stock
80PW - Blk Oversize, .335" (Dozen)
$2.49
In Stock
61PW - Blk X-Long, .335" (Dozen)
$2.49
In Stock
61PW - Black X-Long, .335" (Single)
$0.35
In Stock
81PW - Blk Oversize, .335 (Dozen)
$2.49
In Stock
62OW - Blk Short, Oversize, .350" (Dozen)
$2.49
In Stock
62OW - Blk Short, Oversize, .350" (Single)
$0.35
In Stock
82PW - Blk Oversize, .350" (Dozen)
$2.49
In Stock
63OW - Blk Short, Oversize, .370" (Dozen)
$2.49
In Stock
63OW - Blk, Short Oversize, .370" (Single)
$0.35
In Stock
64OW - Blk Short, Oversize, .400" (Dozen)
$2.49
In Stock
64OW - Blk Short, Oversize .400" (Single)
$0.35
In Stock

Golf Club Wood Ferrules - Black

HUGE GOLF FERRULE SELECTION!

A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!

Not Found

Can you recommend a .335 ferrule that would flow well with a Cobra Myfly+ adapter on a Cobra LTD. The shaft was too prepped too much and can be seen above adapter. 

Asked by: Jules
The Cobra shaft adapter is one solid piece. It does not have a separate ferrule. To try and extend it a little higher possibly the 59PW could be adapted to work.
Answered by: JimY
Date published: 2016-10-10

Could I use a Taylormade bubble shaft with an M1 head? What tip would I need for the bubble shaft?

Asked by: dsik
It would depend on which Taylor Made Bubble shaft you have. Some of the Bubble shafts had tip diameters at .390" to .405". If you have one of these you cannot install it into an M1 head. The shaft tip is just to larger to fit. Some of the later Bubble shafts had a .335" tip diameter shaft and could be used. You would need the TM0023 shaft adaptor. http://www.golfworks.com/taylormade-m1-m2-r-15-sldr-shaft-adaptor/p/TM0023/
Answered by: JimY
Date published: 2016-08-29

Which ferrule best fits a Taylor-Made M2 3HL metal fairway. The shaft is a Fujikura Six? 

Asked by: shanti
You can use any ferrule that is listed as .335" Code# 60PWS will work just fine. The M2 fairways are listed as .335" hosel diameter. Just make sure the shaft you want to use is also .335"
Answered by: Brent Dill
Date published: 2016-08-19

I'm going to be doing a reshaft of a Taylormade M2 fairway, with a Kuro Kage @ .335". What ferrule would be a good matchup with this head?

Asked by: DMacnotGMac
The 60 PW ferrule will work. There is a good chance that Taylor Made used a collared ferrule like the BB0006. http://www.golfworks.com/collared-golf-club-ferrules/p/BB0001/
Answered by: JimY
Date published: 2016-08-15

Looking for a ferrule for a taylormade sldr fairway wood (non adjustable) that would adapt from .350 to .335

Asked by: Scotty123
To size the hosel from .350" down to .335" you could use the Universal Plastic Shim (BB9018) or you could use the SHIM15 and a standard ferrule like the 80PW. http://www.golfworks.ca/universal-shim-with-ferrule-335/p/BB9018/ http://www.golfworks.ca/the-golfworks-brass-adaptor-shims/p/SHIM/ http://www.golfworks.ca/golf-club-wood-ferrules-black/p/60PW/
Answered by: JimY
Date published: 2016-08-08

In your catalog (hard copy) ferrules are available in quantities less than a dozen. Where can you order less than a dozen online?

Asked by: Spartanfan
The single option is listed when you click on the ferrules. For example, if you click on the Taper Tip Iron Ferrules and then click Learn More, they will list as a dozen or a single.
Answered by: GW2002
Date published: 2016-07-20

I have a set of Ping Karsten's, do you have a replacement Ferrule for it? Thanks

Asked by: JS1020
Ping Karsten irons do not use a ferrule. http://www.ping.com/clubs/classics/ironsdetail.aspx?id=16428
Answered by: JimY
Date published: 2016-05-09

What ferrule size do I need for a Cleveland Driver Fujikura Fit On Red Speed Flight shaft to be fitted with the Cleveland XLS Monster Draw 9* head? 

Asked by: Buddy
The Cleveland XLS Monster Draw Driver appears to take a .335 shaft and also appears to use a standard black wood ferrule. Without having one to measure, we can't be totally sure, but the 59 PW .250" length .335 ferrule or the 60PW .500" length .335 ferrule should work.
Answered by: GW2002
Date published: 2016-04-27
  • 2016-12-05T07:50CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_16
  • loc_en_US, sid_60PW, PRD, sort_recentAnswersFirst
  • clientName_golfworks