KBS Hybrid Steel Hybrid Shafts

KBS Hybrid Steel Hybrid Shafts


R Flex - 370 tip (100g) 3B2H
$29.95
In Stock
S Flex - 370 tip (105g) 4B1H
$29.95
In Stock
X Flex - 370 tip (110g) 5C1H
$29.95
In Stock
Pureing 
1-3 $15.50
4+ $13.50
Tip & Butt Trimming
$4.95
Tip Prepping
$2.95

KBS Hybrid Steel Hybrid Shafts

KBS Steel Hybrid Shafts are ideal for today's high performing hybrid club heads.

Features:
  • .370" tip diameter
  • Features a gradual stepless taper starting at the anchor location (between the hands) and continuing to the tip just above the hosel

Trimming Instructions

KBS Trimming Instructions

KBS Hybrid Steel Hybrid Shafts is rated 5.0 out of 5 by 1.
Rated 5 out of 5 by from Very Good Shaft Very smooth shaft Says it is low launch but this is the opposite mid to high and lands soft only downfall was wish there were more in between flexs like the .370 tour steel shafts basically more tip trimming information For the extra cash this is a good shaft though, but you need better tip trimming info.
Date published: 2011-03-21
  • 2016-08-30T07:56CST
  • bvseo_cps, prod_bvrr, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_FS0020, PRD, sort_relevancy
  • clientName_golfworks

Do you have senior flex graphic shafts that will fit a Ping G25 hybrid or a Ping G30 Hybrid. 3H, right hand

Asked by: shhawk
No we do not carry .355" taper tip hybrid shafts. All of the hybrid shafts we carry are either .335" tip or .370". You would need to get the heads bored out to .370" to find the shaft you would want. Once your G25 or G30 gets bored out to .370", your options open up greatly for a shaft you would like.
Answered by: Brent Dill
Date published: 2016-06-02

I have a KE4 Tour 5H 25 degree hybrid head and need to know how much to tip trim the KBS Hybrid stiff shaft I bought to make more of a medium stiff shaft. In trying to follow the charts, I'm guessing 2". Is that correct before I cut?

Asked by: Jon 46
Following our trim code IR32 you would tip trim 2". Since you are installing this into a 25 degree hybrid head which would likely be a little heavier head weight then a 22 degree the shaft may play just a shade more flexible.
Answered by: JimY
Date published: 2015-11-17

Can I use KBS hybrid steel shaft for Ping anser hybrid head?

Asked by: JKim
The Ping Anser Hybrid uses a .355" taper tip shaft and the KBS Hybrid shaft is only available in a .370" parallel tip. So no it will not fit the Ping Anser Hybrid. The head would have to be reamed or rebored to accept a .370" parallel tip shaft.
Answered by: JimY
Date published: 2015-09-09

The tip trim chart on Golfworks as well as KBS only goes to a 22 deg hybrid.  Would you still trim at 2" for a 24-25 deg, or go to 2-1/2" based on the pattern from 14 deg to 22 deg.  Thank you.

Asked by: momonag
I just received a reply from FST on the same question, so I will post it here to close this out. "Thanks for the email.  Tipping the shaft a total of 2” will be plenty.  I wouldn’t recommend tipping it any further for a 24/25 degree hybrid."  Chris - FST
Answered by: momonag
Date published: 2015-08-19
  • 2016-08-30T07:54CST
  • bvseo_cps, prod_bvqa, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_US, sid_FS0020, PRD, sort_recentAnswersFirst
  • clientName_golfworks