Ping i25, G25 & Anser Shaft Adaptor

Ping i25, G25 & Anser Shaft Adaptor

Ping i25, G2 & Anser Shaft Adaptor - RH .335"
In Stock
Ping i25, G2 & Anser Shaft Adaptor - LH .335"
In Stock

Ping i25, G25 & Anser Shaft Adaptor

The Authentic Ping shaft adaptor sleeve allows for multiple shafts to be used in the Ping i25, G25 and Ping Anser drivers and fairway woods along with the 2014 Rapture fairway wood at a fraction of the cost of re-shafting. Available in RH, .335" (Ping Logo on side) and LH,.335".

Ping i25, G25 & Anser Shaft Adaptor is rated 4.0 out of 5 by 1.
Rated 4 out of 5 by from Don't use the rubber cork I re-shafted a i25 driver using this adapter. The small rubber cork was instructed to put in the end of the graphite shaft before glueing. Unfortunately this creates a air lock when pushing in the shaft with epoxy in the collar. I had to push very hard and add a heavy weight to the shaft butt during epoxy drying. Other than that problem it screws right in with the i25.
Date published: 2016-07-29
  • 2016-10-22T07:49CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_PGC001, PRD, sort_relevancy
  • clientName_golfworks

I would like to put a Oban Kiyoshi Shaft in my Ping Answer Driver. Is there an adapter that makes this possible. If so is it a difficult process? Thank you!

Asked by: David
You can install the Oban shaft into the Ping shaft adapter (PGC001) and it will fit into the Ping Anser driver. It is not a difficult process. It is not a difficult process at all if you have the correct tools and epoxy.
Answered by: JimY
Date published: 2016-09-26

Hi would it be possible to purchase ping i25 driver shaft tip from the u.k., what would be total cost with post, regards Terry

Asked by: Terry
We do not have a GolfWorks facility in the UK. Our International Trade Accounts Manager, Donna Ours would be able to help you with the total cost of purchasing this shaft adaptor and shipping cost as well. You can contact her at
Answered by: JimY
Date published: 2016-09-06

what pinh adapter would fit a 2014 ping rapture 3 wood?

Asked by: alex
Yes this shaft adaptor will fit the 2014 Rapture 3 Wood.
Answered by: JimY
Date published: 2016-08-15

how much do you charge to place a ping shaft adalpter on my golf shaft? I will purchase the adapter from you. How long does it take?

Asked by: philpro
For the pricing and turn around time questions you will need to contact our Customer Service Department at or by calling 1-800-848-8358.
Answered by: JimY
Date published: 2016-08-08

what is the insertion depth? how much prep on the tip is needed?

Asked by: 27Jackie
Place masking tape on the shaft to define the limit of prepping and to protect the finish during prep.
Answered by: Guzzzy
Date published: 2016-07-30

How long will it take to get a LH G25 tip

Asked by: Murph
Right now we are not sure as to when the LH G25 shaft adaptor will be in stock. We had them on order from Ping and they shipped RH but not LH. That likely means that Ping currently does not have them in stock. As soon as we get an answer from Ping I will post a reply.
Answered by: JimY
Date published: 2016-07-21

how is ping replacement screw & washer assembled to the adapter?

Asked by: tomy
The Screw and Washer go in from the bottom of the clubhead and up inside the adaptor to tighten and hold the adaptor into the clubhead. The screw is tighten using the ratchet wrench.
Answered by: JimY
Date published: 2016-01-03

Is there any way to remove the shaft from the old adaptor without destroying it?

Asked by: DocHouk
We use this OEM Adaptor Saver Kit for doing this and have had very good success with saving the existing adaptors. You will need to use a product like our Club Shield or something to keep any plastic ferrules cool and from melting when heating.
Answered by: JimY
Date published: 2015-07-14
  • 2016-10-22T07:42CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_21
  • loc_en_US, sid_PGC001, PRD, sort_recentAnswersFirst
  • clientName_golfworks