SEARCH Search GolfWorks
  GolfWorks Canada | Online Catalog | Find the Right Golf Shaft Become a Fan of the GolfWorks
Ping G30 Shaft Adaptor

Ping G30 Shaft Adaptor

Tell a Friend about this item

Product Name Price Status Qty
Ping G30 Shaft Adaptor - RH .335" $27.99 In Stock
Ping G30 Shaft Adaptor - LH .335" $27.99 In Stock

  • Product Description
  • Reviews
  • Questions & Answers
Ping G30 Shaft Adaptor

The Authentic Ping shaft adaptor sleeve adds one more degree of adjustability over the previous Ping adaptors and allows for multiple shafts to be used in the Ping G30 drivers and fairway woods at a fraction of the cost of re-shafting. Available in RH, .335" and LH,.335". The Ping G30 driver and fairway adaptor is not compatible with previous Ping models featuring adjustable hosels

AccessDeniedAccess Denied480F2563A76DA5CDDZV/0+YF5ZVXTYT3BwKMo5APDyRs57zApPnrfMHC6rHQQdLVlBDyJx9KK00BQ0T1

My driver is the g30 adaptor the right one

Asked by: Slang
The G30 adaptor is the correct adaptor for the G30LS.
Answered by: GW2002
Date published: 2015-04-14

Will ping g30 adapter fit a ping anser driver

Asked by: Jmills
The G30 adaptor will not fit into the Anser model driver. Adaptor code PGC001 will fit the Anser.
Answered by: Kevin F
Date published: 2015-04-06

If I purchase a ping g30 shaft adaptor, grip and shaft what would be the assembly charge?

Asked by: bobb
The assembly charge for shaft prepping, cutting and assembly into an adaptor is $16.95. The components (adaptor, shaft & grip) are sold separately. If you purchase a Fujikur Speeder, Pro, Pro Tour Spec or Fuel shaft, the adaptor and the assembly is free. You would only need to purchase the grip in addition to the shaft.
Answered by: Admin
Date published: 2015-03-02

hello is it possible to put an ping anser driver shaft in a g 30 driver

Asked by: willie
The Ping Anser adaptor will not fit into a G30 driver head. You can pull the shaft out of the Anser driver adaptor and insert the shaft into a G30 driver adaptor.
Answered by: Admin
Date published: 2014-12-12

How to install the sleeve on a new shaft?

Asked by: Jmac
Installation of the shaft adaptor is basically the same as installing the shaft into a hosel. Prep the shaft tip by removing any paint finish (graphite shafts) being careful not to sand the composite fiber material. Make sure the inside of the adaptor is clean. If it matters to you, you need to note where the logo on the shaft will be when the adaptor is installed and set to your setting. If it does not matter, then you can install the adaptor on the shaft at any orientation. High strength epoxy is recommened. Dispense the epoxy and mix thouroughly for 30-60 seconds. Apply the epoxy inside the shaft adaptor and to the tip of the shaft. Install the shaft. Wipe off all excess epoxy while it is wet. The outside of the adaptor must be completely clean and free of epoxy or you will not be able to install into the head once cured.
Answered by: GW2002
Date published: 2014-12-02

How does tip trimming the shaft change when using the Shaft Adapter? ?Is it the same as recommended for that shaft?

Asked by: sabergo
Most manufacturers state that the trimming remains the same with adaptors. There is no alteration to the trimming.
Answered by: GW2002
Date published: 2014-11-05

I presume I do not need one of these if I am about to buy a G30 driver and want to try different .335 shafts. As an adpater comes with the driver. Yes? Therefore it is just a replacement part in case I lose or break the original adapter?

Asked by: deB0ZZ
The G30 driver shaft is attached to an adaptor when purchased. The Ping G30 adaptors offer an easy way to try another or multiple new shafts without having to pull your existing shaft from the stock adaptor. The reshafting service charge and adaptor cost are very similar but by purchasing an adaptor for each shaft all shafts can still be used. Another great advantage is that you don't have to be without your driver while its being reshafted. We can install a shaft into and adaptor, cut it to length, install a grip and ship it ready to play.
Answered by: Admin
Date published: 2014-10-09

I know the TaylorMade TP adapters are made of metal where as the other is plastic. The metal tends to weigh more which I liked in a TM club and think I would like in the G30. Do you know what material these adapters are made of??

Asked by: Gilbert
The Ping G30 (PGC002) adaptors are made from aluminum which is the same material used to manufacture all of the TaylorMade adaptors. The only difference is that some of the TaylorMade adaptors have a plastic ferrule attached while the Ping ferrules do not. There isn't a noticeable weight difference between the TM and Ping adaptors.
Answered by: Admin
Date published: 2014-09-15
  • 2015-04-27T07:12CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_12
  • loc_en_US, sid_PGC002, PRD, sort_recentAnswersFirst
  • clientName_golfworks