Rubber Tungsten Tip Weights

Rubber Tungsten Tip Weights

Rubber Tungsten Tip Weight - 8 gram
In Stock
Rubber Tungsten Tip Weight - 10 gram
In Stock

Rubber Tungsten Tip Weights

Flexible rubber tungsten tip weights are ideal for safely adding large amounts of weight to graphite shaft tips. Slotted design allows air to escape during assembly eliminating any chance of built up air pressure causing the shaft to withdraw from the hosel. Available in both 8 and 10 grams.

Rubber Tungsten Tip Weights is rated 4.2 out of 5 by 5.
Rated 5 out of 5 by from Works great These are perfect in adding a lot of weight in a graphite shaft. They do stick out past the hosel but because they're flexible,I never had a problem with shaft breakage. Just make sure to only put a dab of epoxy at the base of the stem near the head and not coat the entire stem. Built about 25 clubs with these, no issues. They can also be easily cut with a knife to adjust the weight which is another huge plus in fine tuning the swing weight.
Date published: 2013-09-08
Rated 5 out of 5 by from A better product These are way better than the tungsten weights designed to do the same job. Unlike the tungsten tip weights, the slot for escaping air is pre-cut, and the rubber mixed in the material won't break. Tungsten sometimes breaks, letting the narrow portion rattle up and down the shaft.
Date published: 2013-03-20
Rated 5 out of 5 by from Just Right for the Job This is me second time to purchase these tip weights. I really like the way they fit and can easily be trimmed/shaved to get the exact weight. For instance I needed about 8 grams to get the weight I wanted; I simply shaved off 2 grams. The rubber material is very soft and easy to work with. Yes they are expensive but at the same time are a quality product. One note; you must realize the tip section will increase the length of the club.
Date published: 2015-09-11
Rated 1 out of 5 by from Too big for shaft opening I know the experts say just drill the tip out with 1/8 inch drill bit. When you drill out material from the tip it loses strength and shaft integrity, come on guys there has to be a better way.
Date published: 2016-09-10
Rated 5 out of 5 by from Easy to use and very accurate weight These are fantastic for adding weight to the head of the club when shafts are shortened to reasonable and playable lengths that allow for better control and more sweet spot strikes.
Date published: 2016-04-23
  • 2016-10-25T08:07CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_GW0121, PRD, sort_relevancy
  • clientName_golfworks

Are these tip ok for .355 graphite.

Asked by: Onethree
Yes these weights can be used with a .355" tip size graphite iron shaft.
Answered by: JimY
Date published: 2016-08-15

when will the 10g weight be available again?

Asked by: TMO
Yes we will have them. We are showing that they should be in stock the first part of next week.
Answered by: JimY
Date published: 2016-06-21

why don't they make the sm. dia of wt.(.175) the same size as 5/32 long drill(.156)? I needed to go from D2 to D5. By cutting off lg.end of wt.& sizing sm. dia. to fit. I was able to slip down graphite shaft with epoxy. lot easier than tungsten powder.

Asked by: Dime60
These weights are designed to go into the tip end of the shaft and the large end wedges in between the bottom of the shaft and the bottom of the hosel of the clubhead. If the weights are to large you can carefully drill a hole in the tip of the shaft just large enough for the weight to fit.
Answered by: JimY
Date published: 2016-05-11

Is any additional tip trimming need when using tip weights?

Asked by: chaney71
The head of the weight will add 1/8" to 3/16" of length. To maintain the correct finished length you would need to cut this amount from the shaft tip assuming that also allows you to have the swingweight you are trying to achieve.
Answered by: JimY
Date published: 2015-11-17

Can these be installed without removing the grips?

Asked by: Bob B Jr
Sure. Slide them in from the tip end with a little epoxy.
Answered by: Ajfgator
Date published: 2015-09-26

Will these work with taper tip shafts? Standard lead tip weights will not...

Asked by: burnerjp
Use .355 wood weights and glue in. Works like a charm!
Answered by: Ajfgator
Date published: 2015-09-26

Are these weights individual or in a pack, if so what is the quantity?

Asked by: Golf Quest
Individual. Price is per single tip weight.
Answered by: Newb
Date published: 2015-07-10

What is the shank diameter of this weight ? The head is how thick ?

Asked by: steve p
The shank diameter is .173". The thickness of the head is .255" and the diameter of the head is .325".
Answered by: JimY
Date published: 2015-01-06
  • 2016-10-25T08:00CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_US, sid_GW0121, PRD, sort_recentAnswersFirst
  • clientName_golfworks