Steel Shaft Butt Extensions

Steel Shaft Butt Extensions


.560 Butt Size Shaft Extension
$2.59
In Stock
.580 Butt Size Shaft Extension
$2.59
In Stock
.600 Butt Size Shaft Extension
$2.59
In Stock
.620 Butt Size Shaft Extension
$2.59
In Stock
Shaft Extension Adhesive - 30 ml. Syringe
$6.99
In Stock

Steel Shaft Butt Extensions

The GolfWorks Steel Shaft Extensions can be used to extend the finished playing length of any steel shafted club. These 12" long steel butt extensions feature an 8 1/2" parallel mid sections that can be cut in the middle to create two 4 1/4" extensions. Each section has a tapered end to perfectly fit inside the shaft being extended. Each extension has a 1 5/8" shaft insertions depth and is chrome plated to prevent rusting.

Steel Shaft Butt Extensions is rated 4.75 out of 5 by 4.
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 4 out of 5 by from Got the job done The fit was nice and snug for the most part, had one that was bent and had to repair, and another that when I test fit it, failed to line up well with the shaft. the other 8 ends were fine. for 3 bucks add an extra extension to make sure your covered. Overall still better than universal extensions I have used in the past and had one break
Date published: 2015-12-27
Rated 5 out of 5 by from Just what I needed Got an incredible deal on some Mizuno irons that were brand new, but came an inch short, so the original owner traded them in. Bought the irons, removed the stock grips, which are lousy anyway, glued in the extenders and put some good grips on. New custom fit set of Mizunos for less than $160. Can't beat that
Date published: 2016-01-05
Rated 5 out of 5 by from Good Deal Nice product! Fit was perfect. Shipping was super fast!
Date published: 2015-12-08
  • 2016-07-26T07:44CST
  • bvseo_cps, prod_bvrr, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_4
  • loc_en_US, sid_S60, PRD, sort_relevancy
  • clientName_golfworks

I want to lengthen my titleist Vokey wedge. What butt size should I order?

Asked by: Paul
For a steel shaft you would use the S60 (.600") shaft extension.
Answered by: JimY
Date published: 2016-07-25

I have Nike Ignite 3 Irons with true temper shafts no idea on the size and don't want to cut the grips off to measure just yet.  Do you know what size these bad boys are?  Also do I just cut these? I want 1.5" extra.

Asked by: Justin1990
That should be a .600" butt diameter shaft and would use the S60 shaft extension. You will sand the post of the extension and also clean the inside of the shaft so that the epoxy will properly bond. Once the epoxy dries you will cut them for the length you want.
Answered by: JimY
Date published: 2016-07-21

How is shaft butt size measured?

Asked by: Timbo
We would use the MAGG grip gauge or a pair of Dial Calipers (GDC) to measure the shaft butt diameter. http://www.golfworks.com/universal-grip-gauge/p/MAGG/ http://www.golfworks.com/digital-caliper-w-led-display/p/GDC/
Answered by: JimY
Date published: 2016-07-21

Before to add extension of 1/2" to the club my swingweight was D1.5 but with the half inch extension my swingweght came down at D0.5.. I am thinking to replace them by the aluminium extension which is lighter. By these numbres above steel look too heavy.

Asked by: Bob 2507
This does not sound correct. When you add 1/2" to a club length the swingweight should get heavier and with an extension generally by 2 to 2.5 swingweights. So if your swingweight was D1.5 to begin with when you added the extension the swingweight should have went to D2.5 to D3. Unless you used heavier grips then what you had installed before. A 4 gram change of grip weight is equal to 1 swingweight. If the grip is heavier the swingweight gets lighter and if the grip is lighter the swingweight gets heavier. The change in swingweight whether you use steel or alunimum will stay the same because it is a factor of added length to the club. The aluminum extension are not that much lighter then the steel extension because the walls are thicker with the aluminum extension for durability. That thickness adds weight.
Answered by: JimY
Date published: 2016-07-12

I have a set of Ping G5 Irons. They are a .600" butt diameter. What size steel shaft extender should I use. I also have a few Cleveland wedges with TruTemper Gold Dynamic shafts. They too are a .600" butt diameter also. Same question.

Asked by: Dewdad
For the .600" butt diameter steel shafts you will use the S60 steel extensions.
Answered by: JimY
Date published: 2016-07-08

I have Mizuno MP 69 irons that have rifle project x 6.5 precision shafts. What size extensions would I need?

Asked by: Johnny smooth
The Project X shafts are a .600" butt diameter and would use the S60 shaft extension.
Answered by: JimY
Date published: 2016-06-20

I have a set of Taylor Made R11 irons with KBS shafts by FST. What size extenders would I need?

Asked by: MFerrell
KBS shafts are a .600" butt diameter and would use the S60 steel shaft extension.
Answered by: JimY
Date published: 2016-06-06

I currently use a set of mizuno mp 57 iron set that are standard length with dynamic gold s300 steel shafts. I want to extend my shafts a 1/2"  My question is, what do you recommend for shaft extenders?

Asked by: Mason
For Dynamic Gold S300 steel shafts I would always recommend the S60 (.600") shaft extension. With shaft extensions I prefer to bond similar materials whenever possible.
Answered by: JimY
Date published: 2016-05-23
  • 2016-07-26T07:42CST
  • bvseo_cps, prod_bvqa, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_71
  • loc_en_US, sid_S60, PRD, sort_recentAnswersFirst
  • clientName_golfworks