Tapered Tip Iron Ferrules . .355"

Tapered Tip Iron Ferrules . .355"


65TI Dozen - Black Std .355" Iron Ferrule
$2.49
In Stock
65TI Single - Black Std .355" Iron Ferrule
$0.35
In Stock
66TI Dozen - Black Long .355" Iron Ferrule
$2.49
In Stock
66TI Single - Black Long .355" Iron Ferrule
$0.35
In Stock
67TI Dozen - Black X-Long .355" Iron Ferrule
$2.49
In Stock
67TI Single - Black X-Long 67TI .355" Iron Ferrule
$0.35
In Stock
75TI Dozen - Black/Chrome Long .355" Iron Ferrule
$3.99
In Stock
75TI Single - Black/Chrome Long .355" Iron Ferrule
$0.50
In Stock
76TI Dozen - Black/Gold Long .355" Iron Ferrule
$3.99
In Stock
76TI Single - Black/Gold Long .355" Iron Ferrule
$0.50
In Stock
Dozen Rubber O-Rings
$2.25
In Stock
Single Rubber O-Ring
$0.35
In Stock

We Also Recommend

Tapered Tip Iron Ferrules . .355"

HUGE?FERRULE?SELECTION! A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!Choose iron ferrules from standard to XX-long lengths. Available as single ferrules or buy ferrules by the dozen.

AccessDeniedAccess DeniedB28BA60E3D4B8F595LZiW26sVZrr+HPBOtBwXCZefkFV48Op+GeaxMPKFB7t6emHHNbVPcsHyDb51o/l

Suggestion on which ferrule for Adams XTD Forged with NS 1050?

Asked by: Begolfing
Personally I would use the 61PW ferrule. They match well to the stock ferrules used by Adams. Even though these are .370" ferrules they will work with .355" taper tip shafts because the taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel. The outside diameter of this ferrule will match closer to the hosel size then the taper tip ferrules.
Answered by: JimY
Date published: 2016-09-12

what size do I need for ping g graphite shaft 335 taper

Asked by: lee
The Ping collared ferrule (BB9047) should also work well with the Ping G irons. http://www.golfworks.com/ping-anser-i-20-355-iron-ferrules/p/BB9047/
Answered by: JimY
Date published: 2016-08-30

What size ferrule would I need for 2014 Taylormade Tour Preferred MC?

Asked by: fairwayNhreen
Taylor Made used a plain black ferrule like the 66TI. Personally I would use the 61PI. It is a .370" ferrule but .355" taper tip shafts have tapered out to approximately .370" where the shaft exits the top of the hosel and the 61PI will match closer to the outside diameter of the hosel then the 66TI. http://www.golfworks.com/golf-club-iron-ferrules-black/p/60PI/
Answered by: JimY
Date published: 2016-08-17

I have nike vrs irons with nippon 915 shafts what ferrell do.i need?

Asked by: bigtom
The information I have shows the Nike VRS irons use a .370" tip diameter shaft. The Nike stock ferrule was a single chrome ring like the 70PI. http://www.golfworks.com/golf-club-iron-ferrules-colored-trim-ring/p/52PIS/
Answered by: JimY
Date published: 2016-08-08

What ferrule would you use for a Ping G Max iron?

Asked by: Hof717
Ping would use a collared ferrule that would be along the lines of our BB0008 ferrules. This is a ferrule for a .370" tip diameter iron shaft but will still work with the .355" taper tip shafts. A .355" taper tip shaft will taper out to approximately .370" where the shaft exists the top of the hosel. The .370" ferrules also match up closer to the outside diameter of the hosel.
Answered by: JimY
Date published: 2016-08-03

so let me get this right. I have a .355 shaft and will need to shim them for a .370 r7 hosel.....will these work or should I use a collard ferrule ?

Asked by: edd
You can use a .355" taper tip ferrule with the shim and be just fine. You could also use a .370" ferrule or a .370" collared ferrule with the shim. .355" taper tip shafts are .355" at the tip and taper out to approximately .370" where the shaft exits the top of the hosel. The .370" ferrules match closer to the outside diameter of the hosel better then the .355" taper ferrules. The 72PI would match up to the original ferrule that Taylor Made used on the R7 irons or you could use the BB0008 Collared Ferrule. You will still need the SHIMT shim.
Answered by: JimY
Date published: 2016-07-26

Which ferrule would I need for a vokey wedge on a KBS c taper 355 shaft?

Asked by: Sgb1000
Actually the Titleist ferrules BB9063 should also work for the Vokey Wedges. http://www.golfworks.com/the-golfworks-ap1-ap2-355-iron-ferrule/p/BB9063/ In the stock taper tip ferrules the 66TI would be the closest match. Personally I use the 61PI ferrules. Even though the shafts are .355" taper tip they taper out to approximately .370" where the shaft exits the top of the hosel so .370" ferrules will fit and generally match the outside diameter closer then the taper tip ferrules.
Answered by: JimY
Date published: 2016-07-11

Which size ferrule would I need for a vokey wedge with a KBS c taper 355 tip diameter shaft

Asked by: Sgb1000
Actually the Titleist ferrules BB9063 should also work for the Vokey Wedges. http://www.golfworks.com/the-golfworks-ap1-ap2-355-iron-ferrule/p/BB9063/ In the stock taper tip ferrules the 66TI would be the closest match. Personally I use the 61PI ferrules. Even though the shafts are .355" taper tip they taper out to approximately .370" where the shaft exits the top of the hosel so .370" ferrules will fit and generally match the outside diameter closer then the taper tip ferrules.
Answered by: JimY
Date published: 2016-07-11
  • 2016-09-28T07:53CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_40
  • loc_en_US, sid_65TIS, PRD, sort_recentAnswersFirst
  • clientName_golfworks