TaylorMade RBZ Shaft Adaptor Sleeve

TaylorMade RBZ Shaft Adaptor Sleeve


TM RBZ Adaptor Sleeve -RH .335" - 3 Degree Offset
$14.99
In Stock
TM RBZ Adaptor Sleeve -LH .335" - 3 Degree Offset
$14.99
In Stock

TaylorMade RBZ Shaft Adaptor Sleeve

Factory adjustable adaptor replacement sleeves for the TaylorMade™ RBZ drivers. Other than replacing a defective Adaptor, the Adaptor Sleeves can also be used to create multiple shaft options for the TaylorMade RBZ driver for less than the cost of simply reshafting your current shaft sleeve.

  • Available in RH/LH - .335" and .350"
  • 3 degree offset
  • Ferrule is pre-assembled for easy assembly

TaylorMade RBZ Shaft Adaptor Sleeve is rated 3.6666666666666665 out of 5 by 3.
Rated 1 out of 5 by from adaptor It didn't work so I trash canned it. Then I bought another adaptor from you and tried to install it on the shaft I bought from you [335] and it doesn't fit. So give another shaft that fits and I might change my mind about now having nothing. Disappointed.
Date published: 2015-10-08
Rated 5 out of 5 by from Sleeve Adapter Was Perfect Needed to replace a broken shaft and this lh adapter sleeve fit the RBZ Tour head perfectly. Nice to have this great driver back in play.
Date published: 2016-03-22
Rated 5 out of 5 by from Quick Service Delivery was very quick and service was great. I will use golf works
Date published: 2016-01-28
  • 2016-08-30T07:54CST
  • bvseo_cps, prod_bvrr, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en_US, sid_TM0017, PRD, sort_relevancy
  • clientName_golfworks

need a sleeve for a 3 fairway wood

Asked by: ron
I believe the TM0017 adaptor should also fit the 3 wood.
Answered by: JimY
Date published: 2016-08-22

If I remove the stiff shaft from a Taylor Made RBZ three wood and want to install a senior shaft that already has a shaft adapter sleeve installed on it, do I just need to purchaseTaylor made R500 shaft adapter and install into 3 wood head?

Asked by: Action Jack
The RBZ 3 wood used a .350" tip diameter shaft. If the Senior flex shaft is a .335" tip diameter then you will need the BB9008 adaptor to fit the .335" shaft into the .350" hosel bore. If the Senior flex shaft is a .350" tip size then the BB9009 adaptor will work. http://www.golfworks.com/taylormade-r5-r7-burner-and-super-quad-adaptor/p/BB9008/
Answered by: JimY
Date published: 2016-08-08

I have a RBZ tour model, the tip says upright on it, is there also a neutral or flat tip available?

Asked by: Jakep55
The TM0017, which is the only adaptor we have available for the RBZ, just has Std. Loft, Higher and Lower markings. Higher is going to close the face and make the lie angle a little more upright and Lower will open the face angle and make the lie angle a little flatter.
Answered by: JimY
Date published: 2016-08-01

Is this part meant for the driver shaft of the first rbz rocketballz driver?

Asked by: Jeremy
The TM0017 adaptor is for the original RBZ driver and the RBZ TP driver.
Answered by: GW2002
Date published: 2016-07-05

does this match up to the adaptor that is now in the broken driver head. so that I need to only use the part for the new shaft?

Asked by: william e long
The stock adapter for the RBZ driver was for a .350" tip diameter shaft. You can use the TM0017 adapter for a .335" tip diameter shaft and install it into this driver without any problems. We no longer stock the TM0017 adapter for a .350" shaft size.
Answered by: JimY
Date published: 2016-06-27

When do you expect the backordered TM RBZ Adaptor Sleeve - .350" to be available?  I have been unable to find them anywhere and would hate to abandon my RBZ that has served me so well (my shaft came unglued and damaged the adaptor sleeve).

Asked by: Ktoo
We have the Right Hand .350" adaptor in stock but not the Left Hand. We will not be getting any more of the Left Hand adaptors in stock. They have been discontinued. You can use the Right Hand adaptor in a Left Hand club. the markings will be reversed but it will fit.
Answered by: JimY
Date published: 2016-03-29

Installing Aldila NVS shaft in the RBZ shaft adaptor, is there any tip trim required? 

Asked by: Nkendle
If this is for the driver no there is no tip trimming. If it is for a fairway wood you would follow the trim chart for the NVS which is W18. http://www.golfworks.com/images/art/shaft_trim_inst.pdf
Answered by: JimY
Date published: 2016-03-09

What is the material of the satin shafts in the RBZ irons? steel or graphite??

Asked by: Jdugan
The stock steel shaft in the RBZ irons would have been a high polished chrome finish so I am assuming these are graphite shafts. If you could give us the name off the shaft it would help us to know for sure.
Answered by: JimY
Date published: 2015-12-03
  • 2016-08-30T08:00CST
  • bvseo_cps, prod_bvqa, vn_cps_3.3.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_17
  • loc_en_US, sid_TM0017, PRD, sort_recentAnswersFirst
  • clientName_golfworks