Finally, a revolutionary technology that will change how you think about iron shafts. UST Mamiya’s new recoil iron shafts are a game changer. In the past, heavy weight graphite iron shafts felt dead and stiff. With UST Mamiya’s exclusive recoil™ technology, we have brought feel back into the shaft, while allowing players to hit a wide range of shots that result in better distance control and pin seeking accuracy.
By positioning over 19 different layers within the shaft, we were able to create a design that outperforms the best steel shafts in the market.
Mid-weight option in a .355 taper tip design.
Designed for more efficient loading and unloading on partial and full shots, providing better distance and trajectory control.
Recoil™ 110 produces a medium to lower shot trajectory.
UST Mamiya Recoil Taper Iron Shafts is rated
5.0 out of
Rated 5 out of
The Greek from
So far so good.I only purchased the shaft for my three iron to test out. My iron set is Mizuno MP4's with KBS C-Taper 120 shafts. Excellent shafts but if I played in a three day tournament they would wear me out. I was skeptical about graphite shafts for my irons but decided to give it a try after researching and reading about the Recoil 110 Stiff shafts. The test so far has been outstanding and if it continues I will replace all my iron shafts with the Recoil. It is true, I cannot tell it is a graphite shaft and the ball explodes off the club face. But as everyone knows the true test is on the golf course. Stay tuned.....
Date published: 2015-11-10
Rated 5 out of
Excellent graphiteshaft ...I have tested many GRAPHITE shafts for IRONS and this is the best one so far.
Date published: 2015-07-30
bvseo_cps, prod_bvrr, vn_cps_3.3.0
co_hasreviews, tv_0, tr_2
loc_en_US, sid_US0087, PRD, sort_relevancy
what is the easiest fitting collard ferrule for recoil 110 on adams xtd forged head thanks
Asked by: golfer
I always use a .370" ferrule with .355" taper tip shafts. Taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel. The .370" ferrule will fit and go on a little easier and fits the outside diameter of the hosel a little better then the taper tip hosel. Ferrule like the 74PI or 61PI would work well. Also during assembly if you put a thin layer of epoxy on the shaft tip before you install the ferrule they will go on a lot easier.
Answered by: JimY
Date published: 2016-03-21
The heads I have the hosel size are .370 what needs to be done to fit them in my heads, the irons I'm talking about are the 2015 callaway apex irons. and what is the cost of that from golf works.
Asked by: mikey
We recommend using our SHIMT which is a brass shim that will shim the .355" taper tip shaft to fit the .370" hosel bore. They work very well for this assembly.
Answered by: JimY
Date published: 2016-03-08
do you know what frequency these would come close to if your were to frequency match them. im looking at the recoil 110 but not sure if I need to get the f4 or f5
Asked by: eddd
There are too many variables involved after assembly like head weight, length and grip size/weight to estimate the exact playing frequency of the shafts. UST recommends that players with a driver swing speed of 90 to 105 use the F4 flex and players with driver swing speeds over 105 use the F5 flex.
Answered by: Admin
Date published: 2015-09-16
Do these shafts hit the ball as far as the project X Pxi?
Asked by: erg1
Shafts of similar weight and flex will most likely produce similar distances, no matter what the material. Generally, a lighter weight shaft has the potential to produce more distance. The only way to know if you, as an individual, will gain distance using one shaft vs. another, is to compare in testing.
Answered by: GW2002
Date published: 2015-06-08
I want to reshaft my mizuno mp64 iron heads with recoil 110 F4 shafts. I play 37 inch lenght on 6 iron and my swing weight is D2. Can you tell me if you can prepare shafts in order that I can install them myself with no drop in my swing weight?
Asked by: Edward
It is hard to say for sure if the swingweight would come out the same. The 37" is 1/4" shorter then what Mizuno lists as a standard length. That will lighten the club by 2 swingweights. If these clubs came directly from Mizuno and they were assembled using heavier then normal clubhead weights then you have a good chance of maintaining the same swingweight at your 37" finished length for the 6 irons, assuming you are using the same model and weight of grips that are currently installed. If these lengths were altered and someone added weight to the clubheads to get the swingweight up to D2 then is would have to be done again to get the D2 swingweight with the Recoil shafts. The other possibility is that the grips were changed to a lighter weight grip that would bring the swingweight up to D2. If this was done and the same grips were used with the Recoil shafts then the D2 swingweight should work out.
When I run a swingweight calculation using the Recoil 110 shaft at 37.25" for the 6 iron with a clubhead weight of 261 grams, a normal 6 iron clubhead weight, and a 50 gram grip the swingweight works out to approximately C9.
We can do the prep work on the shafts but without knowing more information we cannot promise that the swingweights will stay D2.