Collared Golf Club Ferrules

Collared Golf Club Ferrules


BB0002 - Wood .335 - 1/4" length (Dozen)
$3.99
In Stock
BB0003 - Wood .350 - 1/4" length (Dozen)
$3.99
In Stock
BB0005 - Wood .335 - 1/2" length (Dozen)
$3.99
In Stock
BB0007 - Wood .350 - 1/2" length (Dozen)
$3.99
In Stock
BB0006 -Wood .335 - 1/2" length (Dozen)
$3.99
In Stock
BB0004 - Iron .370 - 1/4" length (Dozen)
$3.99
In Stock
BB0008 - Iron .370 - 1/2" length (Dozen)
$3.99
In Stock
BB0001 - Iron .370 - 3/4" length (Dozen)
$3.99
In Stock
BB0009 - Iron .355 - 3/4" length (Dozen)
$3.99
In Stock

Collared Golf Club Ferrules

Collared Ferrules are designed specifically for use with graphite golf shafts. The ferrule collar fits into the club head's hosel to cushion the contact point between the shaft and hosel.

Collared Golf Club Ferrules is rated 4.0 out of 5 by 4.
Rated 5 out of 5 by from nice ferrule I buy these for shafting irons. The 370 are very snug on 370 shafts so they work very well on 355 tapers. Minimal turning if any is required due to size of the ferrules and the collar makes for perfect alignment without having to readjust loft and lie in most cases.
Date published: 2016-02-06
Rated 1 out of 5 by from ferrules The ferrules would not fit the shafts that I purchased at the same time. I had to drill out the inner diameters and in so doing, scuffed up the outer surface.
Date published: 2015-07-27
Rated 5 out of 5 by from Callaway Apex Replacement I broke the Recoil Shaft in my Apex CF 16 #6 Iron. Replaced it using the 3/4" Ferrule and it fit perfect.
Date published: 2016-06-01
Rated 5 out of 5 by from Help Need help with finding a ferrule for my TM aeroburner putting on a .350 tip shaft
Date published: 2017-05-24
  • y_2017, m_6, d_23, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_4
  • loc_en_US, sid_BB0001, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

What ferrules do I need for Titleist 712 mb, and Nike VR pro blades? All require .355 shafts. Also do I use collared or non collared? Thanks

Asked by: Eric
The BB9063 Titleist ferrule should work for the 712 MB irons as well. https://www.golfworks.com/the-golfworks-ap1-ap2-355-iron-ferrule/p/BB9063/ The BB0001 should work for the VR Pro Blades. It is a .370" ferrule but will still work with a .355" taper tip shaft because the shaft tapers out to approximately .370" where the shaft exits the top of the hosel. The Titleist 712 MB irons used a collared ferrule but I am not sure about the VR Pro Blades. If it is not a collared ferrule I would use the 61PI which you could use even if it had a collared ferrule.
Answered by: JimY
Date published: 2017-06-05

What ferrules do I need to reshaft titleist 712 mb, and Nike VR pro blades. All require .355 shafts. Thanks

Asked by: Eric
The BB9063 Titleist ferrule should work for the 712 MB irons as well. https://www.golfworks.com/the-golfworks-ap1-ap2-355-iron-ferrule/p/BB9063/ The BB0001 should work for the VR Pro Blades. It is a .370" ferrule but will still work with a .355" taper tip shaft because the shaft tapers out to approximately .370" where the shaft exits the top of the hosel.
Answered by: JimY
Date published: 2017-06-05

What ferrule is needed for the following: 2011 Taylormade MB .355 RSI TP .355 RSI UDI .355

Asked by: Casey C
These collared ferrules are for .370" tip size shafts but they will work on a .355" taper tip shaft because the shaft tapers out to approximately .370" where the shaft exits the top of the hosel. The BB0001 would be a good replacement for both of these irons. https://www.golfworks.com/collared-golf-club-ferrules/p/BB0001/
Answered by: JimY
Date published: 2017-06-05

Need help finding the right ferrule for a .350 shaft tip and putting it with a TM aero burner driver non tp. 

Asked by: Danntm1332
You could use either the BB0007, which is 1/2" long, or the BB0003, which is 1/4" long. Either one will work.
Answered by: JimY
Date published: 2017-05-24

Hi what ferrules do I need for my 2014 Taylormade Tour Preferred MB irons?

Asked by: Brian86
The BB0001 ferrule will work and match up well to the stock ferrule use by Taylor Made on these irons.
Answered by: JimY
Date published: 2017-05-17

Can you tell me the diameter and depth of the collar for the BB0008 Ferrules? This is for .370 irons. Thanks! The heads I have are Ben Hogan and have a recessed area I'm trying to match.

Asked by: Mark
The collar depth is approximately 3/16" deep and the diameter of the collar is .400".
Answered by: JimY
Date published: 2017-05-15

Purchased 3/4" collared ferrules to reshaft with a Callaway Optifit adapter. They are too big in the sense that the outer diameter extends outside the tip of the adapter too much. The adapter needs a collared ferrule for a sure fit. What ferrule do I need

Asked by: 17tjs
This is the ferrule you will need for the Opti-Fit adaptor - https://www.golfworks.com/callaway-opti-fit-adaptor-ferrule-335/p/BB9096/
Answered by: Admin
Date published: 2017-05-03

Hi, which ferrule will work for installing a Kuro Kage Black shaft into an Aeroburner TP fairway -- both .335 (I believe)? Thanks.

Asked by: mjd8724
Yes the Aeroburner TP fairway woods would be a .335" shaft size. The BB0006 should work well.
Answered by: JimY
Date published: 2017-05-31
  • y_2017, m_6, d_22, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_85
  • loc_en_US, sid_BB0001, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks