Golf Club Iron Ferrules - Black

Golf Club Iron Ferrules - Black


59PI Dozen - Black Short .370" Iron Ferrules
$2.49
In Stock
59PI Single - Black Short .370" Iron Ferrule
$0.35
In Stock
60PI Dozen - Black Std .370" Iron Ferrules
$2.49
In Stock
60PI Single - Black Std .370" Iron Ferrule
$0.35
In Stock
74PI Dozen - Black Long .370" Iron Ferrules
$2.49
In Stock
74PI Single - Black Long .370" Iron Ferrule
$0.35
In Stock
61PI Dozen - Black X-Long .370" Iron Ferrules
$2.49
In Stock
61PI Single - Black X-Long .370" Iron Ferrule
$0.35
In Stock
Dozen Rubber O-Rings
$2.25
In Stock

Golf Club Iron Ferrules - Black

HUGE GOLF FERRULE SELECTION!

A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!

Golf Club Iron Ferrules - Black is rated 4.0 out of 5 by 1.
Rated 4 out of 5 by from 60PI 0.370" Iron Ferrules Purchased these so I could reshaft a 0.370" parallel tip hybrid. They fit very tight onto a 0.370" parallel tip shaft so make sure you have a tool to install them or you will get frustrated or damage your shaft. I drilled a 3/8" hole in a 1" block of wood and used that to get the ferrule started and then finished the insertion by placing the club head on the shaft and hitting down on it until the shaft was fully seated into the club (~1.5"). Be sure to have your tip weights installed first as once these ferrules are on, they can only be removed by cutting them off - I've had to do that before. These could be made a little looser to make the install easier. Otherwise they look good and are exact to sizing. They work much better for 0.355" taper tips.
Date published: 2015-11-05
  • y_2017, m_9, d_25, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_1
  • loc_en_US, sid_60PI, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

I need ferrules that are 370 id and 523 od, due you have them.

Asked by: Jim
We do not have .370" ferrules with that OD measurement. You would need to install the ferrules and finish the size down to fit the hosel OD. The major manufactures finish and size there ferrules during assembly as well.
Answered by: JimY
Date published: 2017-09-18

What ferrule for maltby L tech pured iron shafts A flex? Do you need any special tools?

Asked by: Gisbornedr
We recommend the 56PI ferrule for the LTech irons. It is a good idea to have a ferrule installation tool like the GW1003 to get the ferrule started on the shaft. Ferrules do fit tight. Here is a link from our web site with step by step assembly instructions including ferrule installation that could help you. https://www.golfworks.com/images/art/2008HowToBuildClubs.pdf
Answered by: JimY
Date published: 2017-09-11

What ferrule is recommended for the Taylormade M1 Irons

Asked by: Albee
You could use the Taylor Made Universal ferrule (BB9071) on the M1 irons. https://www.golfworks.com/taylormade-universal-370-iron-ferrule/p/BB9071/
Answered by: JimY
Date published: 2017-09-05

Would like to order a dozen 65 TI ferrules...Can't seem to find them, although a picture is shown. Please advise...Cliff Miller

Asked by: Cliff
At this link the 65TI in a dozen pack is the first one on the list for ordering. https://www.golfworks.com/tapered-tip-iron-ferrules-355/p/65TIS/
Answered by: JimY
Date published: 2017-08-10

What ferrule do you recommend for the mp t7 mizuno wedge?  It's not as long as my mp h5 long irons.  

Asked by: Blake
With Mizuno wedges I would use the 61PI ferrule. It should match the best to the length of the stock ferrule that was used by Mizuno.
Answered by: JimY
Date published: 2017-08-03

Hi I'm looking to order 3 true temper onyx wedge shafts and put them into some taylormade ATV wedges and just wondering which ferrules would be best? Thanks

Asked by: crush9916
I would use the 61PI ferrule with these wedges. The ferrule is a .370" size and the shafts are .355" taper tip but because the shaft tapers out to approximately .370" where the shaft exits the top of the hosel the .370" ferrule will fit. You could also use the Taylor Made Universal ferrule BB9071. https://www.golfworks.com/taylormade-universal-370-iron-ferrule/p/BB9071/
Answered by: JimY
Date published: 2017-08-01

Hi there. I admit I'm experimenting with changing shafts. I want to reshaft a set of r11 irons with Kuro Kage graphite 80 regular shafts.They are .370. Am I correct in getting a .370 ferrule or do i need a different size? 

Asked by: Marc
Yes the R11 irons use a .370" tip size shaft. You could use the Taylor Made Universal .370" collared ferrule BB9071 or the BB0008 collared ferrule. https://www.golfworks.com/taylormade-universal-370-iron-ferrule/p/BB9071/ https://www.golfworks.com/collared-golf-club-ferrules/p/BB0001/
Answered by: JimY
Date published: 2017-07-24

Can I get a lower shipping cost for one small item to be shipped parcel post?

Asked by: roger
You will need to contact Customer Service at 1-800-848-8358 and possibly they can help you.
Answered by: JimY
Date published: 2017-07-19
  • y_2017, m_9, d_25, h_2CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_57
  • loc_en_US, sid_60PI, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks