Golf Club Iron Ferrules - Colored Trim Ring

Golf Club Iron Ferrules - Colored Trim Ring


52PI Dozen - Black/Chrome Std .370" Iron Ferrules
$3.99
In Stock
70PI Dozen - Black/Chrome Long .370" Iron Ferrules
$3.99
In Stock
53PI Dozen - Black/White Std .370" Iron Ferrules
$3.99
In Stock
54PI Dozen - Black/Gold Std .370" Iron Ferrules
$3.99
In Stock
71PI Dozen - Black/Gold Long .370" Iron Ferrules
$3.99
In Stock
55PI Dozen - Black/Red Std .370" Iron Ferrules
$3.99
In Stock
56PI Dozen - Clear/Black/Clear Std .370" Iron Ferrules
$3.99
In Stock
57PI Dozen - Gold/Black/Gold Std .370" Iron Ferrules
$3.99
In Stock
58PI Dozen - Chrome/Black/Chrome Std .370" Iron Ferrules
$3.99
In Stock
72PI Dozen - Chrome/Black/Chrome Long .370" Iron Ferrules
$3.99
In Stock
86PI Dozen - White/Black .370" Iron Ferrule
$4.99
In Stock
73PI Dozen - Gold/Black/Gold .370" Iron Ferrules -
$3.99
In Stock
52PI Single - Black/Chrome Std .370" Iron Ferrule
$0.50
In Stock
70PI Single - Black/Chrome Long .370" Iron Ferrule
$0.50
In Stock
53PI Single - Black/White Std .370" Iron Ferrule
$0.50
In Stock
54PI Single - Black/Gold Std .370" Iron Ferrule
$0.50
In Stock
71PI Single - Black/Gold Long .370" Iron Ferrule
$0.50
In Stock
73PI Single - Long Blk /Gold/Blk .370"" Iron Ferrule"
$0.50
In Stock
55PI Single - Black/Red Std .370" Iron Ferrule
$0.50
In Stock
56PI Single - Clear/Black/Clear Std .370" Iron Ferrule
$0.50
In Stock
57PI Single - Gold/Black/Gold Std .370" Iron Ferrule
$0.50
In Stock
58PI Single - Chrome/Black/Chrome Std .370" Iron Ferrule
$0.50
In Stock
72PI Single - Chrome/BLack/Chrome .370" Iron Ferrule
$0.50
In Stock

Golf Club Iron Ferrules - Colored Trim Ring

HUGE GOLF FERRULE SELECTION! A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!

Not Found.

What size ferrule is standard for graphite irons ? 

Asked by: Red
Most graphite iron shafts will use a .370" size ferrule so any of our ferrules coded PI will work.
Answered by: JimY
Date published: 2017-04-04

Replacing the shaft on an Adams "a12 os" wedge. Using a True Temper TTLITE men's steel shaft "UTTXLIC-43Z". Which ferrule should I use?

Asked by: Buzz
The 70PI looks like it matches well to the stock ferrule that Adams used on these irons.
Answered by: JimY
Date published: 2017-03-27

I'm looking for ferrules for my .355 taper tip project x LZ shafts. Which size do I need?

Asked by: Rjay1302
Any of the Taper tip ferrules we carry will work. The decision is yours as to what length you want on your particular irons. Options are .500 inches, .875 inches or 1.00 inch length.
Answered by: GW2002
Date published: 2017-03-21

I'm shimming a .355 taper tip AeroTech SteelFiber shaft into a .370 hosel on Taylormade Rocketbladez irons.  Which ferrule do I need?

Asked by: SLLoyd
To properly shim these shafts you should use a Shim like the SHIMT (.355 - .370) to make the shaft properly fit the clubhead. The ferrule will not do this. Even with the taper tip shafts you can still use a .370" ferrule size because the shaft tapers out to approximately .370" where it exists the top of the hosel. Taylor Made used a ferrule like the 52PI with these irons. https://www.golfworks.com/golf-club-iron-ferrules-colored-trim-ring/p/52PIS/ https://www.golfworks.com/the-golfworks-brass-adaptor-shims/p/SHIM/
Answered by: JimY
Date published: 2017-03-14

What size ferrules do I need for Dynamic Gold R400U shafts?

Asked by: Tim
The U in R400U indicates that this is a .370" parallel tip shaft and would use a .370" ferrule. Any of the ones listed with the PI on the end will work both in plain black and with trim rings. https://www.golfworks.com/golf-club-iron-ferrules-black/p/60PI/ https://www.golfworks.com/golf-club-iron-ferrules-colored-trim-ring/p/52PIS/
Answered by: JimY
Date published: 2017-03-09

I'm getting ready to restart a set of TM RocketBladeZ irons with new graphite shafts.  I'd like to keep the black with chrome ring.  Which ferrule do you recommend.

Asked by: Bob48
The 52PI will work fine with the Rocketbladz irons.
Answered by: JimY
Date published: 2017-03-06

Which ferrule for Cleveland rtx 2.0 wedge?

Asked by: Bp1
Cleveland uses .355" taper tip shafts in their wedges. The use to use a ferrule like our 75TI which has a single white trim ring at the top. I noticed in looking at a picture they used 2 trim rings on the RTX 2.0 wedge. Cleveland does use longer ferrules on their wedges but that does not mean you have to. It is done more for cosmetics. You could also use a .370" size ferrule. The .355" taper tip shafts taper out to approximately .370" where the shaft exists the top of the hosel so the .370" ferrules will also work and they generally match closer to the outside diameter of the hosel and require less finishing.
Answered by: JimY
Date published: 2017-02-24

Replacing a shaft on a callaway x16 iron. Can and where can I purchase the Ferrals ? Everything I've seen won't match the set ?

Asked by: Shawn
If these are the X16 irons that you have we do not have the exact ferrule. Our BB9003 is the ferrule that we would use for these irons. http://www.callawaygolfpreowned.com/golf-clubs/iron-sets/irons-bb-x16.html https://www.golfworks.com/callaway-collared-iron-ferrule-370/p/BB9003/
Answered by: JimY
Date published: 2017-02-22
  • y_2017, m_5, d_23, h_13CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_47
  • loc_en_US, sid_52PIS, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks