The GolfWorks Enhanced Graphite Shaft Extractor

The GolfWorks Enhanced Graphite Shaft Extractor


The GolfWorks Enhanced Graphite Shaft Extractor
$179.99
In Stock
Broken Graphite Shaft Extractor
$9.99
In Stock
Ratchet Box Wrench
$4.99
In Stock

The GolfWorks Enhanced Graphite Shaft Extractor

We've taken our most popular Graphite Shaft Extractor and made it better! The Enhanced Graphite Shaft Extractor is designed with an internal load sensing spring and indicator. To use, place the club into the device and tighten as you would any screw-type extractor. Tighten until the indicator shows the spring is loaded. Then apply heat. The pressure exerted by the spring is enough to cause the head to slide off once the epoxy breaks down from the heat, but not so much spring pressure that the head shoots off! Your hands remain free, as you don't have to feed pressure while the head starts to move. Improves efficiency and reduces the damage to shafts and heads.

Please Note: Additional shipping charges required due to weight.
Maltby Design Enhanced Graphite Shaft Extractor is rated 4.8 out of 5 by 27.
Rated 5 out of 5 by from Great tool for extracting graphite shafts. I've been removing graphite shafts using a vice, shaft clamp, and a shaft pry bar for years, standing with my feet on the vice mount, applying heat, and prying on the bar. A very physical effort and not a great batting average on saving the shafts. It's really hard to do a completely straight push with a pry bar. I bought a used drive with a Project X Tour S graphite shaft that I really wanted to save and try in another driver, so I ordered the shaft extractor to be sure I could remove it and future graphite shafts. The instructions were easy to follow and I set it up, applied heat with my hot air gun, and when the epoxy broke, the spring pushed the head off. I was very pleased and no damage to the shaft. I would recommend this tool to anyone who wants to pull graphite shafts and reuse them.
Date published: 2015-10-03
Rated 5 out of 5 by from Solid piece of Kit. I bought this specifically to remove shaft adapters without destroying them. At about $25 each they add considerably to a reshaft and are very sensitive to heat. This does the job. I have the adapter removal kit (basically a washer and bolt) that can pull on the adapter instead of pushing it. That works as long as you are patient and use just enough heat. I still like to use my vice and pry bar for most head removals because I am a dinosaur and have been doing it that way since 1990...;-) This is a solid piece of equipment and not flimsy in any way. If I could change something it would be to allow the channel in the bottom to take a standard size piece of wood..
Date published: 2016-09-30
Rated 5 out of 5 by from Simply great! This thing is heavy duty, very well built. The spring loading feature is great - no worries about using too much heat. I was a little skeptical initially thinking the price was a little high but once I received it and put it to use I realized it is worth every single penny! Great tool and great value!
Date published: 2012-12-16
Rated 5 out of 5 by from Excellent Tool Just received this vise on Friday. Mounted it next to my radial arm saw where I cut shafts with a masonry blade (giant Dremel tool). Read the directions for use, and within 30 minutes, I removed two shafts from drivers, thereby, saving me just over $100 in shafts. This is so simple to use. Perfect addition to any hobbyist's (me) or clubmaker's shop.
Date published: 2011-05-03
Rated 5 out of 5 by from saft extracter enhanced This is the best extractor on the market absoultely perfect for the job. Fast and easy to use. No problem for the work needed done. I Strongly recommend this extractor for any level of golf repair.
Date published: 2009-04-09
Rated 5 out of 5 by from saft extracter enhanced This is the best extractor on the market absoultely perfect for the job. Fast and easy to use. No problem for the work needed done. I Strongly recommend this extractor for any level of golf repair.
Date published: 2009-04-09
Rated 5 out of 5 by from Easy to use Bought this for something to fiddle with...very easy to use...I've removed a few graphite shafts and a couple tip adapters...a must have if you are a do it yourself golf nut.
Date published: 2015-07-25
Rated 5 out of 5 by from Excellent Tool Just received this vise on Friday. Mounted it next to my radial arm saw where I cut shafts with a masonry blade (giant Dremel tool). Read the directions for use, and within 30 minutes, I removed two shafts from drivers, thereby, saving me just over $100 in shafts. This is so simple to use. Perfect addition to any hobbyist's (me) or clubmaker's shop.
Date published: 2011-05-03
  • y_2017, m_11, d_22, h_21
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_27
  • loc_en_US, sid_GW1009, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

I have an older model similar to this and its all black. I need a replacement clamp for securing the shaft and I need whatever piece to push against the hosel while the bolt is being moved. how can i get those pieces. Thanks

Asked by: Steggy
We manufacture this graphite shaft puller here at The GolfWorks so can get the replacement parts you need. You will need to call Customer Service at 1-800-848-8358 and they can help you with getting these parts. If you need the Urethane Pads that clamp against the shaft the code is FASRP and the cost is $14.99. The piece that goes over the shaft is the Universal Adaptor Plate (code UAP) and the cost is $7.95.
Answered by: JimY
Date published: 2017-10-10

Hi, just wondering what the weight of the shaft extractor and roughly what it would cost to post to Singapore

Asked by: Baz
For this information it would be best for you to contact our International Trade Accounts Manager, Donna Ours, at dours@golfworks.com and she can answer both of these questions for you.
Answered by: JimY
Date published: 2017-08-02

On sale for $151. but when add to cart comes up $199.

Asked by: Arnie
You need to click on the Banner Ad for the 20% Off Tools and Supplies. Then click on the Enhanced Graphite Shaft Extractor and it will come up with the $151.99 price. https://www.golfworks.com/maltby-design-enhanced-graphite-shaft-extractor/p/GW1009/
Answered by: JimY
Date published: 2017-07-17

Do you have these in stock at your Ottawa Ontario store for local pickup/purchase?

Asked by: Mathc38
Sorry, GolfWorks Canada is located in Ottawa and you can pick this item up at the store. Here is the link for their contact information. You can contact them to get the address. https://www.golfworks.ca/contact-us/a/222/
Answered by: JimY
Date published: 2017-05-10

I want to know if this is available locally in Ottawa so I can come to the store and pick it up and avoid shipping charges. Please advise.

Asked by: mathc38
We show to have 7 units in the Ottawa location.
Answered by: GW2002
Date published: 2017-05-09

Can this graphite shaft extractor  work  on any other shafts besides graphite

Asked by: Fred
Yes it can be used for other shafts besides just graphite. It is not really needed for steel shafts because it is ok to twist and pull a clubhead off of a steel shaft but not a graphite shaft. With graphite shafts they must be forced straight off.
Answered by: JimY
Date published: 2017-05-08

any issues extracting graphite shafts from taylormade adaptors? any additional equipment needed?

Asked by: tedtepe
I would recommend using the OEM Adaptor Saver Kit when pulling shafts from adaptors. The kit is quite easy to use and fits most adaptors. https://www.golfworks.com/oem-adaptor-saver-kit/p/GW0130/ We also sell replacement ferrules for all of the TaylorMade adaptors.
Answered by: Admin
Date published: 2017-05-04

do I need pads? are they included?

Asked by: tedtepe
The pads are included with the extractor. If you clean them periodically they will last for hundreds of shaft pulls.
Answered by: Admin
Date published: 2017-05-04
  • y_2017, m_11, d_22, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_32
  • loc_en_US, sid_GW1009, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks