Ping I20 and G Series Shaft Adaptors

Ping I20 and G Series Shaft Adaptors


Ping I20 and G Series Shaft Adaptor - .335" -
$2.29
In Stock
Ping I20 and G Series Shaft Adaptor - .350" -
$2.29
In Stock

Ping I20 and G Series Shaft Adaptors

Ping shaft adaptor designed for the I20 and all the G series drivers and fairways. Also fits the Ping Rapture and Rapture V2 drivers. Available in both .335" and .350".

Ping I20 and G Series Shaft Adaptors is rated 4.5 out of 5 by 2.
Rated 4 out of 5 by from Ping i20 and G-series shaft adaptors These make it easy to adapt your shaft to the Ping i20 and G-series metalwood heads. The fit is good. My only nit might be the fact that the ferrule head is slightly larger than the my G20 driver hosel so I needed to sand it after install and then use acetone to polish the ferrule. Would like to see them fit exactly so I didn't need to perform this additional step. But not a big deal.
Date published: 2015-10-22
Rated 5 out of 5 by from Shaft adapter works perfectly I reshafted my G15 driver with a more flexible shaft. The adapter worked flawlessly in fitting a .335 shaft into the G15 .350 head. The club is perfect for me reduced swing speed
Date published: 2015-07-09
  • y_2017, m_11, d_22, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_BB9048, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

I have Ping G25 Hybrid and want to reshaft it with a .370 shaft shaved down. which ferrule adapter would I need? Thank you

Asked by: Norboo
Since a taper tip shaft still measures approximately .370" where the shaft exists the top of the hosel you can use a .370" ferrule like the 74PI or a collared ferrule like the BB0008. You would not use one of these adaptor for this assembly.
Answered by: JimY
Date published: 2017-09-18

are these epoxied before shaft is installed?

Asked by: chas
I epoxy them at the same time I install the shaft. I first put epoxy into the hosel then insert the adaptor. I put epoxy on the tip of the shaft and install the shaft into the adptor and install the shaft. Clean up all the excess epoxy and I like to set the club in the playing position to allow the epoxy to dry and cure.
Answered by: JimY
Date published: 2017-07-31

I have a Ping 30 #3 hybrid. I ordered the Nippon N.S. Pro Modus 3 Tour 105 .355" Iron Shaft instead of a graphite shaft. will this shaft fit or will I need to purchase anything else to assemble the club?

Asked by: Ted
Yes the Nippon N.S. Pro 3 Tour 105 .355" taper tip shaft will fit the G30 hybrid. You will need a collared ferrule and the BB9047 Ping i20 ferrule would work with the G30 hybrid as well.
Answered by: JimY
Date published: 2017-07-24

With this shaft adaptor will I be able to connect my G25 shaft to the new G series driver head. 

Asked by: Frankie
The BB9048 adaptors fit the older Ping drivers that do not have an adjustable adaptor. (G10, G15 and G20). The Ping G25 requires a PGC001 adaptor and the G driver requires a PGC002 adaptor. They are not interchangeable between models.
Answered by: Admin
Date published: 2017-05-03

I have the Ping G 3 wood with the adjustable ferrule, do you have a replacement for this?

Asked by: Scott
The PGC002 is the Ping G series adaptor that will fit the #3 wood.
Answered by: GW2002
Date published: 2017-03-20

Will this work on G20 Demo head that has aft fitting cart threaded adapter to use a standard shaft?

Asked by: Hugh18
No these will not work for converting the Ping G20 fitting driver. They are not big enough in diameter. I am not aware of an adaptor that would work for this application.
Answered by: JimY
Date published: 2017-02-24

I have a K!5 3 wood with a TFC Reg shaft. Is it possible to install a Ping G30 soft regular shaft that has the G30 adaptor on it in my K15 fairway. Do I need an adaptor? Do I need to remove the G30 adaptor first.

Asked by: Adrian
Yes you will have to remove the G30 shaft adaptor from this shaft to be able to install it into the K15 driver. The K15 driver use a .350" tip diameter shaft size so you will need to use the BB9048 .335" size to properly install the G30 shaft into the K15 driver. The OEM Shaft Adaptor Saver Kit can be used along with a graphite shaft puller to remove the shaft adaptor from the G30 shaft. http://www.golfworks.com/oem-adaptor-saver-kit/p/GW0130/ http://www.golfworks.com/ping-i20-and-g-series-shaft-adaptors/p/BB9048/
Answered by: JimY
Date published: 2017-01-23

Where can I buy a Ping G30 Driver shaft regular flex TFC 419i with +1" length

Asked by: Dan
Ping would be the only place you can gets the TFC 419i shafts. These shafts are made exclusively for Ping. You would have to send your driver back to Ping to have there shafts installed.
Answered by: JimY
Date published: 2016-11-28
  • y_2017, m_11, d_22, h_2CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_36
  • loc_en_US, sid_BB9048, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks