Ping i25, G25 & Anser Shaft Adaptor

Ping i25, G25 & Anser Shaft Adaptor


Ping i25, G2 & Anser Shaft Adaptor - RH .335"
$21.99
Backordered
Ping i25, G2 & Anser Shaft Adaptor - LH .335"
$21.99
Backordered

Ping i25, G25 & Anser Shaft Adaptor

The Authentic Ping shaft adaptor sleeve allows for multiple shafts to be used in the Ping i25, G25 and Ping Anser drivers and fairway woods along with the 2014 Rapture fairway wood at a fraction of the cost of re-shafting. Available in RH, .335" (Ping Logo on side) and LH,.335".

Ping i25, G25 & Anser Shaft Adaptor is rated 4.5 out of 5 by 2.
Rated 4 out of 5 by from Don't use the rubber cork I re-shafted a i25 driver using this adapter. The small rubber cork was instructed to put in the end of the graphite shaft before glueing. Unfortunately this creates a air lock when pushing in the shaft with epoxy in the collar. I had to push very hard and add a heavy weight to the shaft butt during epoxy drying. Other than that problem it screws right in with the i25.
Date published: 2016-07-29
Rated 5 out of 5 by from Great supplier Thanks just what i needed.I use Golfworks all the time
Date published: 2017-07-17
  • y_2018, m_1, d_20, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_PGC001, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

how deep into the adapter does the shaft go

Asked by: tom
The hosel bore depth is 1.25" deep.
Answered by: JimY
Date published: 2018-01-04

What's the hosel depth for this adapter?

Asked by: 1 dummy
The hosel bore depth is 1.25" deep.
Answered by: JimY
Date published: 2017-12-27

What adaptor do I need for a ping rapture driver?  Thanks 

Asked by: Jwb
For the Ping Rapture driver you need the BB9048 adaptor. If you are installing a .335" tip size shaft order the .335" size and if you are installing a .350" tip size shaft order the .350" size. The Rapture driver came stock with a .350" tip size shaft.
Answered by: JimY
Date published: 2017-12-13

I have an old Ping 3-wood T1st tec or Ti/Zr/+ 12°, unfortunately the shaft broke. Where can I find the ferrule for this particular 3wood? Or can the shaft adaptor mention above work??

Asked by: Anj14528
If you have the TiSi Tec 3 wood you will need the PSSFW Ping adapter. It is listed as the PiSi Fairway wood adapter at this link. https://www.golfworks.com/ping-tisi-adaptors/p/PSS/
Answered by: JimY
Date published: 2017-11-22

I have a G25 Ping driver head and I am looking for a shaft adapter to fit a TFC169D Ping shaft with a .350 Diam shaft tip. 

Asked by: Mike
We do not stock a shaft adapter for the Ping G25 driver that will accept a .350" tip diameter shaft. We can possibly special order an aftermarket Ping G25 adapter for a .350" tip size shaft. You will need to call our Customer Service Department at 1-800-848-8358 and they can help you with the special order.
Answered by: JimY
Date published: 2017-11-22

Is the + and - for loft or close or open on the Ping i25 adapter?

Asked by: Fritz
In their marketing Ping says it adjust loft.
Answered by: JimY
Date published: 2017-10-02

will this work with .335 shafts?

Asked by: chris
Yes the PGC001 Ping adaptor works with a .335" tip size shaft.
Answered by: JimY
Date published: 2017-09-25

Will your Ping Shaft Adaptor PGC002 work with a Ping G25 driver?

Asked by: JohnGolf
No, the PGC002 adaptor will not fit the G25 driver. You need to use the PGC001 for the G25.
Answered by: JimY
Date published: 2017-09-11
  • y_2018, m_1, d_20, h_10CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_37
  • loc_en_US, sid_PGC001, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks