Project X Rifle Steel Iron Set

Project X Rifle Steel Iron Set


5.0 Flex - #3-PW SET .355 tip (115g) - 3.5B1M
$311.99
In Stock
5.5 Flex - #3-PW SET .355 tip (115g) 4B1M
$311.99
In Stock
6.0 Flex - #3-PW SET .355 tip (120g) - 4.5B1M
$311.99
In Stock
6.5 Flex - #3-PW SET .355 tip (125g) - 5B1M
$311.99
Backordered
Pureing 
1-3 $19.50
4+ $17.50
Tip & Butt Trimming
$4.95
Tip Prepping
$2.95

Project X Rifle Steel Iron Set

The Project X Rifle steel iron shaft produces a slightly higher launch angle and penetrating flight pattern. (Services reflect set pricing)

Features:
  • .355" Tip Diameter
  • Features a long taper rate that actually achieves a more dynamic transfer of shaft energy to the ball.
  • Sold as set #3-PW

Trimming Instructions

Not Found.

rifle projectx 6.0 is very little bit hard for me. for this reason, what is the way to make it very little softer? by the way, i neef iron set 3-pw.

Asked by: john
You could switch to a 5.5 flex or you could soft step the 6.0 shafts. If you soft step them 1 shaft by putting the 3 iron shaft into the 4 iron it will soften the 6.0 to approximately a 5.6 or 5.7 flex. Soft stepping the 6.0 keeps the shaft weight the same and changing to the 5.5 makes the shaft more flexible and a little lighter in weight.
Answered by: JimY
Date published: 2017-11-21

i have a set of royal precision frequency matched 6.5 shafts. what would the same flex be in the project x rifle, would it still be a 6.5, albeit my royal precision shafts are at least 20yrs old.

Asked by: antvega71
With the Project X Rifle shafts you would want to drop to a 6.0 flex to match the 6.5 flex of your older set of shafts.
Answered by: JimY
Date published: 2017-11-17

wht is 5.- and 6.0 in relation to r dn s flex?

Asked by: golf dr
5.0 is between and R and S flex. 5.5 is the S flex and 6.0 is between an S and X flex. 6.5 is the X flex.
Answered by: JimY
Date published: 2017-11-15

hi have purchased a 12 month old set of apex pro irons with project X 6.5 shafts.my swing speed shaft is normally 5.5.the club set is 4 iron thu to an including lob wedge (total 9 irons)can you supply me with the set above to australia.if yes how much?

Asked by: rob
Yes we do have the shafts. At this link you will see the Project X shafts individually and it shows them in Australian pricing. You can order from this site or you can contact our International Trade Accounts manager Donna Ours at dours@golfworks.com and she can help you with your order and pricing. https://www.golfworks.com/project-x-rifle-taper-tip-iron-shafts/p/RP0009I/
Answered by: JimY
Date published: 2017-10-26

I have project X 6.0 shafts in my irons now and I've been wanting to make my 3-6 irons all the same length. My question is, can I just cut the butt of the clubs down to match my 6 iron?

Asked by: Jonesy
Single length irons use the same shaft for each iron in the set. Generally the manufacture uses the 6 or 7 iron shafts for each club depending on if the clubs are being made to a 6 or 7 iron length. If you cut the existing shafts down to 6 iron lengths the shafts will have to be built up to create standard grip sizes to match the grip sizes on your 7 iron through wedges. Keep in mind iron heads that are used for single length irons all weight the same and have the same lie angles. You are going to have different swingweights because of different clubhead weights and different lie angles with your 3 through 6 irons.
Answered by: JimY
Date published: 2017-08-21

Hi, would these fit the "maltby-te-forged-irons/p/MA0099/"? I am playing this club with TT-SCORE-LT (bought a MALTBY-PAK) shaft, think these are 0.370, and want to test another shaft. How to downsize shaftdiameter ?

Asked by: Hjalmar
The Maltby TE Forged irons have a Universal Hosel design and you can use either .370" parallel tip or .355" taper tip shafts like the Project X Rifle shafts. If you would like you can use the SHIMT (.355" - .370") shims to center the tip of the .355" taper tip shafts into the TE Forged irons. https://www.golfworks.com/the-golfworks-brass-adaptor-shims/p/SHIM/
Answered by: JimY
Date published: 2017-08-10

I have a 6 iron swing speed of 78 what flex should I order in the Project X rifle?

Asked by: Ed M
Royal Precision referenced an iron swingspeed between 70 and 80 mph would use a 5.0 flex.
Answered by: JimY
Date published: 2017-09-05

Will these shafts fit a Ping G30 iron head?

Asked by: ajgolf
Yes the TRPXISET Project X shafts will fit the Ping G30 irons.
Answered by: JimY
Date published: 2017-10-04
  • y_2017, m_11, d_22, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_28
  • loc_en_US, sid_TRPXISET, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks