Spiral Fluted Reamers

Spiral Fluted Reamers


Spiral Fluted Reamer - .335" Woods -
$26.99
In Stock
Spiral Fluted Reamer - .350" Woods -
$26.99
In Stock
Spiral Fluted Reamer - .370" Irons -
$26.99
In Stock
Heavy Duty Chucking Handle
$9.99
In Stock
Tapered Spiral Reamer - .355" - Tapered Irons -
$29.99
In Stock

Spiral Fluted Reamers

Made of high strength steel for longer life, these precision Spiral Fluted Reamers will remove debris and small amounts of metal from virtually any hosel bore. Available in 4 diameters, .335 & .350 woods - .355" and .370" irons.

Click Here for Spiral Fluted Reamer Instructions
Spiral Fluted Reamers is rated 4.8 out of 5 by 6.
Rated 5 out of 5 by from Easier To Use Than I Thought I had some True Temper Speed Step 80 shafts that I wanted to use in Nike Forged Pro Combo iron heads. Used the .370 reamer bit on the heads, which are .355 diameter with no problem at all. Great purchase and saved lots of money doing it myself. Thanks GolfWorks for having the right tools for the job
Date published: 2016-01-12
Rated 5 out of 5 by from High quality tool This is an excellent tool to size a hosel properly. I use the reamer with a T-handle tapping tool and slowly clean out and size the hosel. Work great to remove old epoxy that a wire brush won't get or to open up an undersize hosel bore.
Date published: 2015-12-03
Rated 4 out of 5 by from .335 diameter reamer Purchased to clean out hosel bores on heads when re-shafting. I thought the very end would have a slight bevel or radius like normal reamers to strengthen the tip. End was ground flat.
Date published: 2016-09-20
Rated 5 out of 5 by from Quality product Reamer worked as intended. I bought this reamer and was able to ream twould sets of .355 heads to .370 pretty easily by hand using a "T" handle.
Date published: 2016-12-09
Rated 5 out of 5 by from Top of the line reamers These reamers work great. Don't need to worry about messing up the hosel size.
Date published: 2017-02-05
Rated 5 out of 5 by from Easy hosel prep. Excellent drill bits. Like a hot knife through butter!
Date published: 2016-01-04
  • y_2017, m_2, d_27, h_18
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_GW0115, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

Could I use this product to clean a hosel that still has pieces of graphite shaft and epoxy. The broken shaft could not completely extract?

Asked by: Drums2go2
It depends on how big a piece of epoxy you have in the hosel. If it is a sliver of epxoy on the side wall of the hosel this will work fine. If it is a bigger piece of epoxy I would likely drill it out.
Answered by: JimY
Date published: 2017-01-30

Which reamer is used to bore .355 iron heads to accept .370 shafts?

Asked by: Harry
You would order the one listed for .370" iron shafts. http://www.golfworks.com/spiral-fluted-reamers/p/GW0115/
Answered by: JimY
Date published: 2016-09-06

Is it possible to change iron head type .355 to .370 parrallel. if so with what reamer tool i need

Asked by: Sergei
Yes it is. You would use the .370" reamer that is listed at this link. http://www.golfworks.ca/spiral-fluted-reamers/p/GW0115/ It is best to do this using a drill press and Reaming & Boring Vise (RBV) http://www.golfworks.ca/reaming-and-boring-vise/p/RBV/
Answered by: JimY
Date published: 2016-03-13

How long are the framers?

Asked by: Crandyl
I am not sure what you mean by framers but I took some measurements and hopefully I have gotten you the correct measurement. The square section at the top measures 3/8" long. The length of the full post including the square section measures 1 7/8". The lengths of the flutes measures 1 5/8".
Answered by: JimY
Date published: 2016-01-25

I have .355 taper hosel.  can i use bit to make hosel .355?

Asked by: ragbag
If you have a .355" hosel bore iron you could use the .355" tapered reamer to clean out that hosel bore. If you are converting a .355" hosel bore to a .370" hosel bore you would use the .370" iron reamer.
Answered by: JimY
Date published: 2015-11-27

Are these suitable for cleaning out the hosel of a club following pulling of the shaft?

Asked by: WPackman
They could be used for cleaning out the hosel during reshafting. Generally they are used primarily to change a hosel bore size. We generally use Wire Brushes for cleaning the hosel bores. http://www.golfworks.com/product.asp?pn=GW1060 http://www.golfworks.com/product.asp?pn=gw1061
Answered by: JimY
Date published: 2015-10-06

how much metal can this reamer remove and do u just use a tap handle for use

Asked by: kenny
I have personally never used this by hand with the tap handle but I am told it will work just fine. Generally with golf clubs we are not removing more then .015" of material.
Answered by: JimY
Date published: 2015-04-16

can you use these reamers enlarge a 0.355" hosel to 0.370"?

Asked by: onespeed
  • y_2017, m_2, d_27, h_14CST
  • bvseo_bulk, prod_bvqa, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_9
  • loc_en_US, sid_GW0115, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks