Spiral Fluted Reamers

Spiral Fluted Reamers

Spiral Fluted Reamer - .335" Woods -
In Stock
Spiral Fluted Reamer - .350" Woods -
In Stock
Spiral Fluted Reamer - .370" Irons -
In Stock
Heavy Duty Chucking Handle
Tapered Spiral Reamer - .355" - Tapered Irons -
In Stock

Spiral Fluted Reamers

Made of high strength steel for longer life, these precision Spiral Fluted Reamers will remove debris and small amounts of metal from virtually any hosel bore. Available in 4 diameters, .335 & .350 woods - .355" and .370" irons.

Click Here for Spiral Fluted Reamer Instructions
Spiral Fluted Reamers is rated 4.9 out of 5 by 10.
Rated 5 out of 5 by from Easier To Use Than I Thought I had some True Temper Speed Step 80 shafts that I wanted to use in Nike Forged Pro Combo iron heads. Used the .370 reamer bit on the heads, which are .355 diameter with no problem at all. Great purchase and saved lots of money doing it myself. Thanks GolfWorks for having the right tools for the job
Date published: 2016-01-12
Rated 5 out of 5 by from High quality tool This is an excellent tool to size a hosel properly. I use the reamer with a T-handle tapping tool and slowly clean out and size the hosel. Work great to remove old epoxy that a wire brush won't get or to open up an undersize hosel bore.
Date published: 2015-12-03
Rated 5 out of 5 by from Good results Used to clean up shaft holes on some putters that went underwater in the Texas flood. Took some time a predrilling on the rusted shafts but worked to get the remaining rust out. Both putters back in service
Date published: 2017-12-03
Rated 4 out of 5 by from .335 diameter reamer Purchased to clean out hosel bores on heads when re-shafting. I thought the very end would have a slight bevel or radius like normal reamers to strengthen the tip. End was ground flat.
Date published: 2016-09-20
Rated 5 out of 5 by from Quality product Reamer worked as intended. I bought this reamer and was able to ream twould sets of .355 heads to .370 pretty easily by hand using a "T" handle.
Date published: 2016-12-09
Rated 5 out of 5 by from Great tool A reamer is a needed part of any club building shop, and golf works is the place to shop
Date published: 2017-07-09
Rated 5 out of 5 by from Works great. I bought it to give a shot at boring out my wedges by myself. Worked perfectly.
Date published: 2017-03-15
Rated 5 out of 5 by from Top of the line reamers These reamers work great. Don't need to worry about messing up the hosel size.
Date published: 2017-02-05
  • y_2018, m_1, d_20, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_en_US, sid_GW0115, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

Snapped off a shaft in my irons. Time replace all shafts. Will the 0.355 reamer remove the old rusted shaft or do you recommend drilling? What size drill bit do I use to take out the old rusted shat end?

Asked by: HollywoodDon
No the Reamer will not cut down into the shaft. You need to use a drill bit. We would use the letter T size bit which is .358" to drill out this piece. https://www.golfworks.com/drill-bits/p/GW1045/
Answered by: JimY
Date published: 2018-01-09

Is there a reamer to make an older set of hogan princess irons playable ...going from the older .270 taper tip to modern .355 tip? Thanks 

Asked by: Ryan
No we do not have a reamer that would work with these irons. Reamers are designed to remove small amounts of material. With these heads you would need to rebore them to get them to a .355" tapered hosel bore. I would start with smaller drill bits and gradually enlarge the bore until I get the bottom of the bore to approximately .355". For reboring a .355" hosel bore we end up using a letter T size drill bit which measures .358" and we drill all the way to the bottom of the hosel bore. Next we would use a letter U size bit which measures .368" and we would drill down approximately two thirds of the depth of the bore. Lastly we use a 3/8" bit which measures .375" and we drill down one third of the depth of the bore. With this .270" bore I would start with a 9/32" (.281") and drill to the bottom of the bore. Next a 5/16" (.312") and then an 11/32" (.343") before starting with the letter T size bit. Doing is this way keeps the bit centered in the hosel bore and help to keep from changing the bore angle. We sell the T, U and 3/8" bits in a set of cobalt bits. The code is DBCSET and you will find them at this link. https://www.golfworks.com/drill-bits/p/GW1045/
Answered by: JimY
Date published: 2017-11-20

Will the .370 reamer take a .355 hosel to .370 on a small 1/4hp drill press?

Asked by: PGSLLC
Absolutely,The reamer is only removing 0.015 of material,next to nothing,thats about .0075 per side..... approx. the width of 2 human hairs,make sure you secure the head properly,even a reamer can bite and break,and don't forget to use a cutting fluid,keeps the reamer sharp and allows it to cut more efficiently....be well
Answered by: slapthecabbage
Date published: 2017-06-05

Could I use this product to clean a hosel that still has pieces of graphite shaft and epoxy. The broken shaft could not completely extract?

Asked by: Drums2go2
It depends on how big a piece of epoxy you have in the hosel. If it is a sliver of epxoy on the side wall of the hosel this will work fine. If it is a bigger piece of epoxy I would likely drill it out.
Answered by: JimY
Date published: 2017-01-30

Which reamer is used to bore .355 iron heads to accept .370 shafts?

Asked by: Harry
You would order the one listed for .370" iron shafts. http://www.golfworks.com/spiral-fluted-reamers/p/GW0115/
Answered by: JimY
Date published: 2016-09-06

Is it possible to change iron head type .355 to .370 parrallel. if so with what reamer tool i need

Asked by: Sergei
Yes it is. You would use the .370" reamer that is listed at this link. http://www.golfworks.ca/spiral-fluted-reamers/p/GW0115/ It is best to do this using a drill press and Reaming & Boring Vise (RBV) http://www.golfworks.ca/reaming-and-boring-vise/p/RBV/
Answered by: JimY
Date published: 2016-03-13

How long are the framers?

Asked by: Crandyl
I am not sure what you mean by framers but I took some measurements and hopefully I have gotten you the correct measurement. The square section at the top measures 3/8" long. The length of the full post including the square section measures 1 7/8". The lengths of the flutes measures 1 5/8".
Answered by: JimY
Date published: 2016-01-25

I have .355 taper hosel.  can i use bit to make hosel .355?

Asked by: ragbag
If you have a .355" hosel bore iron you could use the .355" tapered reamer to clean out that hosel bore. If you are converting a .355" hosel bore to a .370" hosel bore you would use the .370" iron reamer.
Answered by: JimY
Date published: 2015-11-27
  • y_2018, m_1, d_21, h_10CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.6
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_11
  • loc_en_US, sid_GW0115, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks