Steel Shaft Butt Extensions

Steel Shaft Butt Extensions


.560 Butt Size Shaft Extension
$2.59
In Stock
.580 Butt Size Shaft Extension
$2.59
In Stock
.600 Butt Size Shaft Extension
$2.59
In Stock
.620 Butt Size Shaft Extension
$2.59
In Stock
Shaft Extension Adhesive - 30 ml. Syringe
$6.99
In Stock

Steel Shaft Butt Extensions

The GolfWorks Steel Shaft Extensions can be used to extend the finished playing length of any steel shafted club. These 12" long steel butt extensions feature an 8 1/2" parallel mid sections that can be cut in the middle to create two 4 1/4" extensions. Each section has a tapered end to perfectly fit inside the shaft being extended. Each extension has a 1 5/8" shaft insertions depth and is chrome plated to prevent rusting.

Steel Shaft Butt Extensions is rated 4.7 out of 5 by 10.
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 5 out of 5 by from Good fit and great price. Used the .600 extenders to bring my club shafts up to standard length. Fit and finish was good. I sanded the small end, coated with epoxy, and cut them to correct length. I did trim the male ends first to minimize swingweight impact. they were longer than needed. I've had no problems at all and the clubs are performing just fine playing 3 times a week. I waited until it was time to replace the grips to add the extensions so with the added length and new grips it's been like playing with a new set of clubs. Very satisfied and as always great service from Golfworks.
Date published: 2017-04-25
Rated 4 out of 5 by from Got the job done The fit was nice and snug for the most part, had one that was bent and had to repair, and another that when I test fit it, failed to line up well with the shaft. the other 8 ends were fine. for 3 bucks add an extra extension to make sure your covered. Overall still better than universal extensions I have used in the past and had one break
Date published: 2015-12-27
Rated 5 out of 5 by from Just what I needed Got an incredible deal on some Mizuno irons that were brand new, but came an inch short, so the original owner traded them in. Bought the irons, removed the stock grips, which are lousy anyway, glued in the extenders and put some good grips on. New custom fit set of Mizunos for less than $160. Can't beat that
Date published: 2016-01-05
Rated 5 out of 5 by from Proper Butt Extension Size I'm looking to extend two sets of vintage irons with steel butt extensions and need to know the proper size. 1. MacGregor DX2 irons 2. MacGregor Tourney REC; M85 with the small head Your recommendations are appreciated.
Date published: 2017-06-21
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 4 out of 5 by from Ease of Use The extensions are great for lengthening clubs and are easy to work with.
Date published: 2017-09-09
Rated 4 out of 5 by from Grips The grips were just what I expected. The delivery was on time with no problems.
Date published: 2017-01-27
  • y_2017, m_9, d_18, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

What size butt shaft extension will fit Rifle 5.5?

Asked by: Ken
Rifle shafts are a .600" butt diameter and use the S60 (.600") steel extension.
Answered by: JimY
Date published: 2017-09-05

I have callaway x 16 rifle shafts what is the shaft diameter at the butt end?

Asked by: Buck
Rifle shafts are a .600" butt diameter and use the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-08-15

What butt size for a standard Taylor made steel shaft

Asked by: Dru
It could vary depending on which steel shaft and flex but more then likely it would use the S60 (.600") steel extension.
Answered by: JimY
Date published: 2017-08-07

What is .520 or .620 size stand for

Asked by: Chris
With steel shaft extensions you match the extension size to the outside diameter measurement at the butt end (grip end) of the shaft. If your shaft is a .600" butt diameter you would use the S60 extension etc. S56 = .560" butt diameter shaft S58 = .580" butt diameter shaft S60 = .600" butt diameter shaft S62 = .620" butt diameter shaft If you need extensions and are not sure what size you need we might be able to help you. If you can tell us the shafts you have, manufacture, model and shaft flex, there is a good chance we can tell you what size extension you need.
Answered by: JimY
Date published: 2017-08-28

which extensions fit store bought talor made shafts

Asked by: Mike
With most of the Taylor Made stock steel shafts the S60 steel extension should work.
Answered by: JimY
Date published: 2017-07-25

i have a set of ping g20 irons steel shafts CTS that i want to extend 1/2 inch which extender do i need 5-sw

Asked by: philip
Those shafts are a .600" butt diameter and would use the S60 steel extension.
Answered by: JimY
Date published: 2017-08-04

If I have a set of True Temper XP 115 R shafts with a butt end size of .605 and I need to extend them 1", which one of these extension sizes should I purchase? Thank you.

Asked by: Jason N
You could use the S60 steel extension and I would mix some Quik Center (QCSB) with the epoxy to center and tighten the fit. You could also use the Universal Extension (GW1047) with this shaft. https://www.golfworks.com/the-golfworks-quick-center-shafting-beads/p/QCSB/ https://www.golfworks.com/universal-golf-shaft-extensions/p/GW1047/
Answered by: JimY
Date published: 2017-07-18

With a shaft diameter of .560, what size grip should I use? Normally I use a midsize grip on my other clubs.

Asked by: Martin47
You will have to use grip build up tape to increase the shaft size to match the grip core size. If the grip core size is .600" you would need to add 4 strips of the 2" BU2 grip build up tape to bring the shaft size up to .600". You can then install the double sided grip tape and install the grip.
Answered by: JimY
Date published: 2017-07-11
  • y_2017, m_9, d_18, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_196
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks