Steel Shaft Butt Extensions

Steel Shaft Butt Extensions


.560 Butt Size Shaft Extension
$2.59
In Stock
.580 Butt Size Shaft Extension
$2.59
In Stock
.600 Butt Size Shaft Extension
$2.59
In Stock
.620 Butt Size Shaft Extension
$2.59
In Stock
Shaft Extension Adhesive - 30 ml. Syringe
$6.99
In Stock

Steel Shaft Butt Extensions

The GolfWorks Steel Shaft Extensions can be used to extend the finished playing length of any steel shafted club. These 12" long steel butt extensions feature an 8 1/2" parallel mid sections that can be cut in the middle to create two 4 1/4" extensions. Each section has a tapered end to perfectly fit inside the shaft being extended. Each extension has a 1 5/8" shaft insertions depth and is chrome plated to prevent rusting.

Steel Shaft Butt Extensions is rated 4.6 out of 5 by 5.
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 4 out of 5 by from Got the job done The fit was nice and snug for the most part, had one that was bent and had to repair, and another that when I test fit it, failed to line up well with the shaft. the other 8 ends were fine. for 3 bucks add an extra extension to make sure your covered. Overall still better than universal extensions I have used in the past and had one break
Date published: 2015-12-27
Rated 5 out of 5 by from Just what I needed Got an incredible deal on some Mizuno irons that were brand new, but came an inch short, so the original owner traded them in. Bought the irons, removed the stock grips, which are lousy anyway, glued in the extenders and put some good grips on. New custom fit set of Mizunos for less than $160. Can't beat that
Date published: 2016-01-05
Rated 4 out of 5 by from Grips The grips were just what I expected. The delivery was on time with no problems.
Date published: 2017-01-27
Rated 5 out of 5 by from Good Deal Nice product! Fit was perfect. Shipping was super fast!
Date published: 2015-12-08
  • y_2017, m_2, d_26, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

what size should i get for 33 1/2 in taylormade daytona 12 putter?

Asked by: james
I am not sure what butt diameter shafts Taylor Made uses in their putters. Over the years .580" has been a common butt diameter for putter shaft in which case the S58 (.580") steel extension would work. I am not sure at 33.5" if the diameter would drop to .560" (S56). Taylor Made Customer Service is closed today (President's Day) so I am unable to verify the butt diameter for sure.
Answered by: JimY
Date published: 2017-02-20

I was going to reshaft a set of MizunoMP4 irons i recently purchased as they are 1/2" too short. They are currently using ProjectX 5.5 rifle shafts with a tip of.355 and but of.600. Do i order the .600 option and new grips? these go under the grips right?

Asked by: Sean951
You would need the S60 (.600") extension for the Project X 5.5 shafts. The extension are epoxied into the butt end of the shaft under the grip.
Answered by: JimY
Date published: 2017-02-20

hello which size of butt shaft extension for a 33" steel shaft scotty cameron putter please?

Asked by: fred
Cameron normally uses a .580" butt diameter putter shaft. That would use the S58 (.580") steel extension. However if you have shortened the putter to 33" the butt diameter could be smaller then .580" and you may need the S56 (.560") extension.
Answered by: JimY
Date published: 2017-02-10

I have some Eye 2 BeCu irons with Microtaper shafts....what size extension would I need for those shafts?  Thanks!

Asked by: Willy
These would use the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-02-06

I wan to extend an old Wilson 8802 putter. Which butt shall I go to?

Asked by: YSS
I would expect this to be a .580" butt diameter shaft and use the S58 (.580") shaft extension.
Answered by: JimY
Date published: 2017-01-30

I want to extend some .580 shafts just 1/2 inch with these steel extensions, but I don't want to add more weight to butt end than necessary. What's the shortest I could cut tapered insert length and epoxy in butt and be sure extension will end up secure?

Asked by: Mac
I always want the post going into the shaft to be longer the the extension length I am adding. In a case like this using a steel shaft extension I would cut the post to 3/4" so that it would be 1/4" longer then my extension length of 1/2". I always tried to stay 1/4" longer with the post on these steel extension. It comes down to what liability you are comfortable with.
Answered by: JimY
Date published: 2017-02-14

I have an odyssey black series #9 and was looking to extend it. I was wondering what the butt diameter is that is needed for this.  Thanks

Asked by: John87
That should be a .580" butt diameter putter shaft and use the S58 (.580") extension.
Answered by: JimY
Date published: 2017-01-26

What size would be needed for steel AP2? Thanks

Asked by: Jon
I need to know what steel shafts are in your AP2 irons. Please tell me the brand, model and shaft flex. You can email me at jyachinich@golfworks.com.
Answered by: JimY
Date published: 2017-01-26
  • y_2017, m_2, d_27, h_2CST
  • bvseo_bulk, prod_bvqa, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_141
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks