Steel Shaft Butt Extensions

Steel Shaft Butt Extensions


.560 Butt Size Shaft Extension
$2.59
In Stock
.580 Butt Size Shaft Extension
$2.59
In Stock
.600 Butt Size Shaft Extension
$2.59
In Stock
.620 Butt Size Shaft Extension
$2.59
In Stock
Shaft Extension Adhesive - 30 ml. Syringe
$6.99
In Stock

Steel Shaft Butt Extensions

The GolfWorks Steel Shaft Extensions can be used to extend the finished playing length of any steel shafted club. These 12" long steel butt extensions feature an 8 1/2" parallel mid sections that can be cut in the middle to create two 4 1/4" extensions. Each section has a tapered end to perfectly fit inside the shaft being extended. Each extension has a 1 5/8" shaft insertions depth and is chrome plated to prevent rusting.

Steel Shaft Butt Extensions is rated 4.8 out of 5 by 9.
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 5 out of 5 by from Good fit and great price. Used the .600 extenders to bring my club shafts up to standard length. Fit and finish was good. I sanded the small end, coated with epoxy, and cut them to correct length. I did trim the male ends first to minimize swingweight impact. they were longer than needed. I've had no problems at all and the clubs are performing just fine playing 3 times a week. I waited until it was time to replace the grips to add the extensions so with the added length and new grips it's been like playing with a new set of clubs. Very satisfied and as always great service from Golfworks.
Date published: 2017-04-25
Rated 4 out of 5 by from Got the job done The fit was nice and snug for the most part, had one that was bent and had to repair, and another that when I test fit it, failed to line up well with the shaft. the other 8 ends were fine. for 3 bucks add an extra extension to make sure your covered. Overall still better than universal extensions I have used in the past and had one break
Date published: 2015-12-27
Rated 5 out of 5 by from Just what I needed Got an incredible deal on some Mizuno irons that were brand new, but came an inch short, so the original owner traded them in. Bought the irons, removed the stock grips, which are lousy anyway, glued in the extenders and put some good grips on. New custom fit set of Mizunos for less than $160. Can't beat that
Date published: 2016-01-05
Rated 5 out of 5 by from Proper Butt Extension Size I'm looking to extend two sets of vintage irons with steel butt extensions and need to know the proper size. 1. MacGregor DX2 irons 2. MacGregor Tourney REC; M85 with the small head Your recommendations are appreciated.
Date published: 2017-06-21
Rated 5 out of 5 by from Sweet Add-On 4 Big Man.. Being a 6'3" guy with "monkey" arms. These cut to 1" extension brought my new/used irons to my old irons standard. No more slicing...sweet. Note one extension does 2 irons.
Date published: 2009-08-26
Rated 4 out of 5 by from Grips The grips were just what I expected. The delivery was on time with no problems.
Date published: 2017-01-27
Rated 5 out of 5 by from Good Deal Nice product! Fit was perfect. Shipping was super fast!
Date published: 2015-12-08
  • y_2017, m_6, d_27, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

On the golf shaft extension, what does the .560 mean.

Asked by: Skinny
The .560 indicates what the outside diameter of the larger portion of the extension is. A .560 extension would be used to extend a shaft with a .560 butt diameter.
Answered by: GW2002
Date published: 2017-06-16

I have a Titleist Vokey wedge, standard length.  What size extension should I buy. The shaft says SM6 Wedge Flex.

Asked by: Seth
Titleist lists the stock shaft as a Dynamic Gold and that would use the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-06-14

I have ping CFS shafts don't know what size extenders

Asked by: Bob Q
That should be the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-06-13

I have a set of Tommy Armour irons with the Tommy Armour Tour Step II Regular flex steel shafts. What size steel extender do I need to get?

Asked by: Bill D
It should use the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-06-13

What size do I order for True Temper Dynamic Gold X100's?

Asked by: BC27
The DG X100 uses the S60 (.600") steel shaft extension.
Answered by: JimY
Date published: 2017-06-12

Hello I am not sure what Butt size to get: I have two different shafts in my irons KBS Tour 90 and a NS Pro 105T - could you help me with the Butt size? Thanks.

Asked by: mtuhoop24
Both of these shafts have a .600" butt diameter and would use the S60 (.600") steel extensions. At these links if you scroll down the page to the specifications box you will see the specifications for these shafts including the butt diameter. That can help you in the future. https://www.golfworks.com/kbs-tour-90-taper-tip-steel-iron-shafts/p/FS0023/ https://www.golfworks.com/nippon-ns-pro-modus-tour-105-golf-shafts/p/NP0016/
Answered by: JimY
Date published: 2017-06-07

I need a shaft extension for my set of dynamic golf s300.what size do I need to buy from you?

Asked by: Tucks
Dynamic Gold S300 will need the S60 extension.
Answered by: GW2002
Date published: 2017-06-02

My shaft label says True Temper Dynalite Gold Sensicore. Your chart says 580 shaft but 580 extension is too large. Can you advise what extension is correct? For older Wilson Staff Tour Blade irons. Thanks. And availabile inSan Antonio Golf Galaxy store?  

Asked by: Steady 70
If these are .355" taper tip R300 flex then the butt end should be 580". I personally played Dynalite shafts for years. Possibly there is a build up of chrome on the end of the extension that is keeping it from going in. Once it is sanded it should fit. Also if the shaft had been cut with a tube cutter then the butt end will be pinched in and that would keep the extension from fitting. You would need to sand the butt end of the shaft to remove where it had been pinched in and then install the extension.
Answered by: JimY
Date published: 2017-05-31
  • y_2017, m_6, d_27, h_5CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_185
  • loc_en_US, sid_S60, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks