Tapered Tip Iron Ferrules . .355"

Tapered Tip Iron Ferrules . .355"


65TI Dozen - Black Std .355" Iron Ferrule
$2.49
In Stock
65TI Single - Black Std .355" Iron Ferrule
$0.35
In Stock
66TI Dozen - Black Long .355" Iron Ferrule
$2.49
In Stock
66TI Single - Black Long .355" Iron Ferrule
$0.35
In Stock
67TI Dozen - Black X-Long .355" Iron Ferrule
$2.49
In Stock
67TI Single - Black X-Long 67TI .355" Iron Ferrule
$0.35
In Stock
75TI Dozen - Black/Chrome Long .355" Iron Ferrule
$3.99
In Stock
75TI Single - Black/Chrome Long .355" Iron Ferrule
$0.50
In Stock
76TI Dozen - Black/Gold Long .355" Iron Ferrule
$3.99
In Stock
76TI Single - Black/Gold Long .355" Iron Ferrule
$0.50
In Stock
Dozen Rubber O-Rings
$2.25
In Stock
Single Rubber O-Ring
$0.35
In Stock

We Also Recommend

Tapered Tip Iron Ferrules . .355"

HUGE?FERRULE?SELECTION! A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!Choose iron ferrules from standard to XX-long lengths. Available as single ferrules or buy ferrules by the dozen.

Not Found.

Are the 66TI tapered iron black ferrules about 7/8" long? I have a set of Titleist AP2 forged irons about 7 years old & the ferrules appear to be about 7/8" long. I'm changing out the iron shafts & I want to match the same ferrules. Thx.

Asked by: Mac
The 66TI ferrules are .875" in length (7/8").
Answered by: GW2002
Date published: 2017-03-21

I am installing .355 KBS shafts into Maltby TE Irons (universal bore). Should I use a .355 ferrule? Also, when installing .355 shafts into .370 bore (using a shim), what size ferrule should I use? Thanks!

Asked by: BrettB64
You could use either a .355" taper tip ferrule or a .370" parallel tip ferrule with the .355" taper tip shafts. The .355" taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel so the .370" ferrules will fit and they will match closer to the outside diameter of the hosels and require less sizing and finishing. This would also be true if you are using a shim.
Answered by: JimY
Date published: 2017-03-20

What do I use for the Callaway Apex Pro 16 with UST Mimaya Recoil 95 .355 taper shaft?

Asked by: WXMan2112
The Callaway BB9051 ferrule should work well. https://www.golfworks.com/callaway-collared-355-ferrule/p/BB9051/
Answered by: JimY
Date published: 2017-03-15

Hello, I would like to know the OD of my irons golf club which is mizuno MP4. My ID is .355. Thnks for your answer

Asked by: Fred
Mizuno MP4 irons use a .355" taper tip shaft and you can use either a .355" taper ferrule. Mizuno used a plain black ferrule like the 66TI. You could also use the 61PI which is a.370" ferrule. .355" taper tip shafts taper out to approximately .370" where the shaft exists the top of the hosel so .370" ferrules will fit and the .370" ferrule will match closer to the outside diameter of the hosel and require less sizing and finishing. https://www.golfworks.com/golf-club-iron-ferrules-black/p/60PI/
Answered by: JimY
Date published: 2017-03-14

I am reshafting my Taylor Made R9 6 iron with a Project x 5.5 .355 taper tip.  The stock ferrule has the double crome ring. Which ferrule should I use for this project?

Asked by: Bill OB
The Taylor Made R9 irons used a .370" parallel tip shaft and the R9 TP irons used a .355" taper tip shaft. You could use the 72PI ferrule. Even though it is a .370" ferrule it will still fit the Project X 5.5 .355" taper tip shafts because .355" taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel. https://www.golfworks.com/golf-club-iron-ferrules-colored-trim-ring/p/52PIS/ If you have the R9 irons and not the R9 TP you will need to use a shim to make the .355" taper tip shafts fit properly. Our SHIMT (.355 - .370) works well for this installation. https://www.golfworks.com/the-golfworks-brass-adaptor-shims/p/SHIM/
Answered by: JimY
Date published: 2017-02-27

how long is the 65TI ferrule; how long is the 66TI?

Asked by: jimc629
The 65TI is 1/2" long and the 66TI is 7/8" long. At this link scroll down the page to the green specification box and you can see this measurement for these ferrules. https://www.golfworks.com/tapered-tip-iron-ferrules-355/p/65TIS/
Answered by: JimY
Date published: 2017-02-22

what is outer diameter size

Asked by: Ely
Scroll down the page to the green specification box and all the OD measurements for these ferrules are listed. http://www.golfworks.com/tapered-tip-iron-ferrules-355/p/65TIS/
Answered by: JimY
Date published: 2017-02-06

Reshafting Cleveland forged 588 CD with XP 95 shaft. Which Ferrule would you suggest?

Asked by: YSS
Cleveland used a ferrule that was in the 3/4" to 7/8" range so a ferrule like the 66TI or 75TI at 7/8" long could work. You could also use a ferrule like the 61PI which is a .370" ferrule size. .355" taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel so the .370" ferrules will fit and they match closer to the outside diameter of the hosel and require less sizing and finishing.
Answered by: JimY
Date published: 2017-01-30
  • y_2017, m_3, d_27, h_1CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_58
  • loc_en_US, sid_65TIS, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks