Tapered Tip Iron Ferrules . .355"

Tapered Tip Iron Ferrules . .355"


65TI Dozen - Black Std .355" Iron Ferrule
$2.49
In Stock
65TI Single - Black Std .355" Iron Ferrule
$0.35
In Stock
66TI Dozen - Black Long .355" Iron Ferrule
$2.49
In Stock
66TI Single - Black Long .355" Iron Ferrule
$0.35
In Stock
67TI Dozen - Black X-Long .355" Iron Ferrule
$2.49
In Stock
67TI Single - Black X-Long 67TI .355" Iron Ferrule
$0.35
In Stock
75TI Dozen - Black/Chrome Long .355" Iron Ferrule
$3.99
In Stock
75TI Single - Black/Chrome Long .355" Iron Ferrule
$0.50
In Stock
76TI Dozen - Black/Gold Long .355" Iron Ferrule
$3.99
In Stock
76TI Single - Black/Gold Long .355" Iron Ferrule
$0.50
In Stock
Dozen Rubber O-Rings
$2.25
In Stock
Single Rubber O-Ring
$0.35
In Stock

We Also Recommend

Tapered Tip Iron Ferrules . .355"

HUGE?FERRULE?SELECTION! A complete selection of ferrules with modern outside diameters that match perfectly to the outside diameter of our hosels. All ferrules have a 19° countersink which allows a cushion of epoxy to form between the top of the hosel and the inside of the ferrule, strengthening the bond. Each ferrule also is “pre-washed,” arriving at your shop with a high-gloss finish and no need for an acetone wipe to make it shine!Choose iron ferrules from standard to XX-long lengths. Available as single ferrules or buy ferrules by the dozen.

Not Found.

Are any of your black 355 or 370 ferrules 7/8" long?

Asked by: Dave
At this link if you scroll down the page you will see the green specification box for these ferrules and you will see the lengths listed. .875" is 7/8" long. https://www.golfworks.com/tapered-tip-iron-ferrules-355/p/65TIS/
Answered by: JimY
Date published: 2017-06-20

I have a set of Mizuno mix-25 irons that I fitting into exsar tour spec .355 graphite shafts. Which ferrules should I order. Are they the collared ones?

Asked by: Cowboy916
I do not know for sure if the MX-25 irons used a collared ferrule. Personally I would use the 61PI ferrules to match the original Mizuno ferrules. The 61PI is a .370" size ferrule but because .355" taper tip shafts taper out to approximately .370" where the shaft exits the top of the hosel they will fit and they match closer to the outside diameter of the hosel. https://www.golfworks.com/golf-club-iron-ferrules-black/p/60PI/
Answered by: JimY
Date published: 2017-06-19

What ferrules should I use to reshaft my Titleist 712MB with Nippon modus 120X shaft? Thanks!

Asked by: Ron_Panda
The BB9063 would also work for the 712MB Titleist irons. https://www.golfworks.ca/the-golfworks-ap1-ap2-355-iron-ferrule/p/BB9063/
Answered by: JimY
Date published: 2017-06-07

What ferrule should I buy if I have a set of Mizuno MP-H5?

Asked by: jma
The 66TI would closely match the length of the stock ferrule Mizuno used on the MP-H5 irons. Personally I would use the 61PI ferrule with these irons. It is a .370" size ferrule but .355" taper tip shaft taper out to approximately .370" where the shaft exits the top of the hosel so they will fit. They also match up closer to the outside diameter of the hosel and require less finishing and sizing.
Answered by: JimY
Date published: 2017-06-06

I have the 2004 Mizuno JPX-EZ with 0.355 steel shafts. What ferrules should I use when replacing shafts?

Asked by: Yuan
You could use the 66TI. It would match close to the stock ferrule Mizuno used. Personally I would use the 61PI. It is a .370" ferrule but .355" taper tip shafts taper out to approximately .370" where the shaft exists the top of the hosel so it will work well and will match closer to the outside diameter of the hosel and require less finishing.
Answered by: JimY
Date published: 2017-05-12

i have taylor made rsi2 irons what ferrule do i need

Asked by: jeff
The BB9071 is a Taylor Made replacement ferrule and will work well with the Rsi 2 irons. https://www.golfworks.com/taylormade-universal-370-iron-ferrule/p/BB9071/
Answered by: JimY
Date published: 2017-04-24

I need ferrules for KBS .355 tapered shafts, to be used with Adams CMB forged irons. Can you help?

Asked by: Mike
Personally I always use a ferrule like the 61PI with a .355" taper tip shaft. .355" taper tip shafts taper out to approximately .370" where the shaft exists the top of the hosel so the .370" ferrule will fit and they match closer to the outside diameter of the hosel and require less finishing. Or you could use the 65TI which will work well.
Answered by: JimY
Date published: 2017-04-28

Are the 66TI tapered iron black ferrules about 7/8" long? I have a set of Titleist AP2 forged irons about 7 years old & the ferrules appear to be about 7/8" long. I'm changing out the iron shafts & I want to match the same ferrules. Thx.

Asked by: Mac
The 66TI ferrules are .875" in length (7/8").
Answered by: GW2002
Date published: 2017-03-21
  • y_2017, m_6, d_23, h_9CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_66
  • loc_en_US, sid_65TIS, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks