The GolfWorks Brass Adaptor Shims

The GolfWorks Brass Adaptor Shims


15 (.335 - .350) - 5 pack
$3.99
In Stock
30 (370 - .400) - 5 pack
$3.99
In Stock
T (.355 - .370) - 5 pack
$3.99
In Stock

The GolfWorks Brass Adaptor Shims

These shims are the perfect answer to your shaft installation headaches. Easy to use, they center the shaft in the bore perfectly and create a maximum bond between the shaft and the hosel. Each pack comes with 5 shims.

The GolfWorks Brass Adaptor Shims is rated 5.0 out of 5 by 2.
Rated 5 out of 5 by from Work for me I buy and use the shims in cases where a sleeve is not log enough to properly support the shaft to the bottom of the bore. What can I say, they are shims. I haven't had a problem with quality or dimensions.
Date published: 2016-06-20
Rated 5 out of 5 by from Brass Shim For Orlimar 420 I used the brass shim to replace the shaft on an Orlimar Hip Ti 420. I had to use two shims as the hosel was .370. It worked great. the driver feels solid when hit.
Date published: 2015-08-17
  • y_2017, m_3, d_24, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_SHIM, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

I am replacing the shaft on a Ping G15 with a .335 shaft. Do I need to use both a shim and an adaptor BB9048 .335 to make it work? Thanks.

Asked by: Tom
You could use either the SHIM15 and a standard ferrule like the 60PW or you could use the BB9048 the one listed for .335" but you do not need to use both.
Answered by: JimY
Date published: 2017-02-28

Re-shafting my Cobra Big Trusty 55*. Your data says .355 shaft. Both the new shaft and factory shaft are a very loose fit. Noticed a collar on factory ferrule that seems to center it. Which shim do I need so I can use a custom ferrule?

Asked by: Scott3usa
If you are using a .355" taper tip then the SHIMT (.355" - .370") should work the best.
Answered by: JimY
Date published: 2017-02-20

Am I able to remove a head with a shim in it?  If so, is it any different than a normal removal?

Asked by: Jmack
Removing a shaft that has been installed with a Shim is the same as a normal shaft removal.
Answered by: JimY
Date published: 2017-02-06

Would you be kind enough to go through the sequencing using epoxy and shims? i.e. .355 to a .370 hosel. Thx, Joe

Asked by: bigeoj
The way I always do this assembly is to get everything ready and organized. I would install the ferrule on the shaft and set it almost to it's proper depth. Then put epoxy into the clubhead and just insert or start the the shim into the top of the hosel. I do not want to close up the finger of the shim as this will make it more difficult to start the shaft into the shim. I then roll the tip of the shaft in epoxy and insert it into the shim and push the shaft and shim all the way into the hosel. I then hold the clubhead in one hand and the shaft in the other and tap the butt end of the shaft against the floor to make sure that the shaft and shim are installed all the way to the bottom of the bore. Next I clean up the excess epoxy and set the club to dry.
Answered by: JimY
Date published: 2017-01-09

Will this work for .335 to .355

Asked by: shooter77
We do not have a shim that will allow you to shim a .335" shaft into a .355" hosel bore. Keep in mind a .355" taper hosel bore is only .355" at the very bottom and it tapers out to approximately .370" where the shaft exits the top of the hosel. So at the top of the hosel you need to shim .035" and at the bottom of the hosel you need to shim .020". You would have to create a shim to make this work and I would always remind you of the liability that goes along with doing this.
Answered by: JimY
Date published: 2016-12-05

Instead of a shim to epoxy a .335 shaft in to a .350 bore can I simply use extra GOLFWORKS shaft centering granuals?

Asked by: John
No you need tou use a SHIM. The Quik Center (QCSB) will not fill enough space to keep the shaft properly centered in the hosel bore.
Answered by: JimY
Date published: 2016-12-02

I have some Taylormade firesole irons with .390 hosel ID. I want to put .370 parallel shafts in. Will the shim 30s work?

Asked by: Joe
The SHIM 30 would be to big for this installation. You could possibly adapt the SHIM 15 and also use some Quik Center (QCSB) to help keep the shaft centered in the bore. http://www.golfworks.com/the-golfworks-quick-center-shafting-beads/p/QCSB/ The way these were most commonly reshafted was using the SADI Bushing Ferrule Adapter. The iron adapter is sized to fit a .400" hosel bore and you would carefully sand it down to fit the .390" bore. It is sized to accept the .370" shaft size. http://www.golfworks.com/bushing-ferrule-adaptors/p/SADW/
Answered by: JimY
Date published: 2016-11-21

I have a complete set of King Cobra II Oversize irons with a variety of shafts. These, I believe, have the .380 hosel. Which shims would work to reshaft these with standard .370 shafts?

Asked by: CP1953
The King Cobra II Oversize irons were a .380" hosel bore size. We do not have a specific shim size for this installation. I would use the SHIM15 and you may need to remove one or two of the fingers from the shim to get it to size correctly and that is not a problem. http://www.golfworks.com/the-golfworks-brass-adaptor-shims/p/SHIM/
Answered by: JimY
Date published: 2016-08-29
  • y_2017, m_3, d_24, h_18CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_26
  • loc_en_US, sid_SHIM, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks