True Temper Dynamic Gold SL .370" Steel Iron Shafts

True Temper Dynamic Gold SL .370" Steel Iron Shafts

R300 - 370 tip (104g) 3B1H
In Stock
S300 - 370 tip (109g) 4C1H
In Stock
X100 - 370 tip (109g) 5C1H
In Stock
1-3 $19.50
4+ $17.50
Tip & Butt Trimming
Tip Prepping

True Temper Dynamic Gold SL .370" Steel Iron Shafts

The Dynamic Gold SL steel wood shaft weighs 20% less than Dynamic Gold and offers all the same performance characteristics.

  • .370" tip diameter
  • Light weight design increases club head speed yielding greater distance
  • Constructed from revolutionary S3 alloy
  • Ideal for low to mid handicap golfers seeking tour playability in a superlite design
  • Identical appearance and performance as Dynamic Gold with less fatigue

Trimming Instructions

True Temper Dynamic Gold SL .370" Steel Iron Shafts is rated 5.0 out of 5 by 2.
Rated 5 out of 5 by from Glad I switched! I finally pulled the Uniflex steel shafts that came in my Callaway Razr irons. Glad I made the switch!! The DG SL feels much better and lighter. The Uniflex felt like iron bars. I have only played a few rounds but I think I picked up about half a club in length also!
Date published: 2016-04-22
Rated 5 out of 5 by from Very good shaft Installed shafts for a friend in his wedges. They were lighter and better kick point, he loves them.
Date published: 2016-06-22
  • y_2017, m_11, d_22, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_TT201105, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_golfworks

Looking to replace a Taylor made s-90 in a tm 200 iron (2002). Would this be suitable. Your chart's do not have an option

Asked by: Golfman3000
The Dynamic Gold SL would have different playing characteristics then the S90 used by Taylor Made in this club but it would match fairly close in weight. The DG SL is designed to produce a low ball flight and the S90 would have been designed to produce a high ball flight. If those playing characteristics fit you better than the DG SL could be a good choice. If you want a shaft to play more like the S90 a shaft like the FST 115 (FS0012) could be a better choice. It is listed at 115 grams but is 43" raw length and once cut for installation it will weight in the mid to high 90 gram weight range.
Answered by: JimY
Date published: 2017-11-03

Do you have a standard tip trim chart for True Temper S300 Dynamic Gold golf shafts?

Asked by: Terry Campbell
Dynamic Gold S300 parallel .370" tip size shafts follow trim code IR2 which is on page 2 at this link.
Answered by: JimY
Date published: 2017-06-06

I currently have the Callaway Apex CF16 (3-AW) w/ TT XP 95 x100, and need the DG SL to lower the trajectory and keep swing weight similar. I'm not sure on hosel depth, but I do play the lengths 3 iron 39.5"-AW 35.5". Can you prep them to those specs?

Asked by: Rod
Yes we can prep the shafts for your playing lengths for these clubs. When you place your order you will need to tell us that you have the Apex CF16 irons.
Answered by: JimY
Date published: 2017-04-25

I have 85 mph with iron 6 and i need 1/2 inch more standard lenght.the hosel of club head is deep 32 mm can we use true temper sl R 104 grams or i need S 109 grams?

Asked by: Leonard
If you are wanting the club to play as an R flex then purchase the R flex and cut it 1/2" longer at the grip end and you will be fine.
Answered by: JimY
Date published: 2017-04-03

I have 85 mph with iron 6 : is possibile with this speed make shaft 1/2 inch more than standard lenght with shaft R 104 grams?

Asked by: Leonard
Yes, after assembly the shafts will be approximately 1 1/2" to 2" longer than standard length. You will need to butt trim the shafts after assembly. Simply cut the shafts as long as needed.
Answered by: Admin
Date published: 2017-08-07

I need 1/2 inch more standard club with 85 mph Speed of club  S Flex is right? Then i must cut 1" for the iron 3 and then cut the butta until 39.5 inch? Thanks

Asked by: Leonard
Yes you would cut 1" from the tip end, install the shaft into the 3 iron and then cut from the butt end to your finished length of 39.5".
Answered by: JimY
Date published: 2017-03-27

Are this shaft iron parallel tip and same trimming istruction like s300 dinamic gold 130 grams?

Asked by: Leonard
Yes the Dynamic Gold SL parallel tip irons shafts follow trim code IR2 which is the same as the Dynamic Gold.
Answered by: JimY
Date published: 2017-03-27

How much do I trim off irons 4-gw. Do we still do back of heel to first step per iron?

Asked by: Jim
The trimming instructions are listed online and in our catalog. For the parallel tip TT201105 Dynamic Gold SL irons you tip trim 1.5" from he tip on the 4 iron, 2" on the 5, 2.5" on the 6, 3" on the 7, 3.5" on the 8, 4" on the 9, and 4.5" on the Pitching Wedge and Gap Wedge. After tip trimming and installation, you trim to final playing length from the but end of the shaft.
Answered by: GW2002
Date published: 2017-02-17
  • y_2017, m_11, d_22, h_2CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_16
  • loc_en_US, sid_TT201105, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_golfworks