Universal Golf Shaft Extensions

Universal Golf Shaft Extensions

Universal Golf Shaft Extensions - 3 Pack
In Stock
Shaft Extension Adhesive - 30 ml. Syringe
In Stock

Universal Golf Shaft Extensions

The Universal Shaft extensions will work with almost any steel or graphite shaft. After applying a little epoxy, insert the extension into a shaft, force the provided tapered plug into the extension until the extension expands to fit the ID of the golf shaft. Its that simple. 3 per pack.
Universal Golf Shaft Extensions is rated 4.416666666666667 out of 5 by 12.
Rated 4 out of 5 by from Universal Shaft extension These were easy to install. I added epoxy to the mix so they are not going anywhere. I did mess one up but a heat gun can melt the epoxy and it was easy to remove. You can also drill through the plug with a long bit. I have been playing the set I extended for about 4 rounds now. None of the extensions have come loose or gotten squirrely. These are light so they don't add much weight to the club. I now have a set of forged bladed irons long enough for me to play and I really enjoy the old school Ben Hogan feel of them.
Date published: 2012-02-28
Rated 5 out of 5 by from Worked Great I used these extensions on a set of graphite shafted irons to extend them all 1/2 inch. The openings were .490. To make these extensions work I used a hacksaw on the end along the two slot openings. I also used a razor to take additional material off the slot until the extension compressed into the shaft without too much force. Once I was comfortable with the fit, I inserted them with epoxy. I also dipped the pin tips in epoxy before driving them into the extension. These extensions are there to stay.
Date published: 2016-07-01
Rated 5 out of 5 by from Universal shaft extensions Installed these on steel shafts to gain .5 inch increase under new multicompound grip replacement. Have played several rounds with them and have had no problems. The extensions are very solid, secure and lightweight.
Date published: 2015-08-31
Rated 5 out of 5 by from Easy to install This was the first time I'd ever regripped a set of clubs or used extensions, these made it all too easy! Very happy with them!
Date published: 2015-12-21
Rated 1 out of 5 by from Didn't fit The universal extension that was shipped to me did not fit my set of Cleveland Hybrids with a shaft opening of .490.
Date published: 2016-03-01
Rated 5 out of 5 by from Shaft adapters purchased 3weeks ago were very user friendly and adjusted to the diameter of the shaft for proper fit.
Date published: 2015-07-24
Rated 5 out of 5 by from Well Made Worked great when the extension that I already had was to large to insert. Fit snug....no issues.
Date published: 2016-07-19
Rated 5 out of 5 by from Universal golf shaft extensions Great product. Good in steel or fiberglass shafts. They stay very secure!!!!
Date published: 2016-08-14
  • 2016-10-22T07:40CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_12
  • loc_en_US, sid_GW1047, PRD, sort_relevancy
  • clientName_golfworks

Will this fit a Cleveland 588 altitude with Matrix Radix Sv R flex shaft and  miyazaki  c. Kua 39 A or R  flex shafts? Thanks

Asked by: Oca
Yes the Universal Extension should fit both of these shafts.
Answered by: JimY
Date published: 2016-09-06

Will these fit a putter shaft? 

Asked by: Mike
Yes this will work in a steel shafted putter.
Answered by: JimY
Date published: 2016-09-01

Is that extension will work with Adila Rogue "Silver" reg. butt size .635

Asked by: bob
The GW1047 extension might work but I have measured this shaft and the GW4000 Silver (.575") coded extension fits well. http://www.golfworks.com/premium-graphite-shaft-extensions/p/GW4000/
Answered by: JimY
Date published: 2016-08-01

Will these extensions work on clevland 588 altitude irons with Actionlite shafts with a 600 butt end?

Asked by: WILFRED
The Universal Extension will not fit these graphite shafts. With the ActionLite being a very light weight shaft the USGE extension should be the one that will fit the best. http://www.golfworks.com/graphite-shaft-extensions/p/GSE/
Answered by: JimY
Date published: 2016-03-08

I assume the extension should be cut to the required extension length first, so as making it easier to insert the expansion insert? Correct?

Asked by: Wedge
You could cut it to length first or you could install it and then cut it to length. With the Universal Extension being able to get the pin installed in the proper place is very important so if cutting to length first helps you to do this then I would suggest cutting first.
Answered by: JimY
Date published: 2016-02-23

How long are these extensions ?

Asked by: ralpham
They will add 3" of length.
Answered by: JimY
Date published: 2016-01-07

Can this be used to fix a broken putter shaft

Asked by: brii
Depends where the break is located. These extensions are only 3" in length. If the break is at or near the top of the handle this extension would work. If the putter is broken somewhere in the middle, you probably need to buy a putter shaft.
Answered by: Chuck45
Date published: 2015-08-04

Will this fit into a Scotty Cameron standard length putter shaft? Thank you.

Asked by: LMRLMR
This should work. Depending on which Cameron putter you have and which shaft it has Cameron putter could have either a .580" butt diameter shaft and other models will have .600" butt diameter shafts.
Answered by: JimY
Date published: 2015-04-13
  • 2016-10-22T07:47CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_US, sid_GW1047, PRD, sort_recentAnswersFirst
  • clientName_golfworks