True Temper Command .370" Steel Iron Shafts

True Temper Command .370" Steel Iron Shafts

R/S Flex - 370 tip (127g) 3/4C1M
In Stock
1-3 $15.50
4+ $13.50
Tip & Butt Trimming
Tip Prepping

True Temper Command .370" Steel Iron Shafts

The True Temper Command is True Temper's best priced steel iron shaft.

  • .370" tip diameter
  • Competitively priced for use in virtually any golf club

Trimming Instructions

True Temper Command .370" Steel Iron Shafts is rated 5.0 out of 5 by 2.
Rated 5 out of 5 by from Quality and great price Cost plays a big factor in my 5 star rating. That said, Most low cost steel iron shafts offer some compromise from comparable designs costing more money. I bought these shafts several years ago and they have seem time in several different irons and they have found a home in a set of original Maltby MMB's. They replaced some S300 SL's that launched too high, spun too much and ballooned to often. These shafts are on the heavier side, launch perfectly with my Digger Driver swing. I have a set of X100's I was going to soft step in these heads but I am so happy with the Commands I've decided to stick with them. I tipped these a 1/4" over recomended tipping for stiff. If you prefer a lower launch, heavier shaft, at a value price you can't go wrong with these.
Date published: 2013-09-09
Rated 5 out of 5 by from Not Sure Yet Just re-shafted a set of CB-2 Blacks with the Tru Temper Command shafts. Going to play tomorrow. They feel great right now but time on the course and range will tell!! Bought a grip kit with the shafts and I love the way GolfWorks cuts the tape and the little spray bottle of solvent!! Made it much easier to do the project in my living room lol!!!! More to come on the Shafts
Date published: 2013-11-23
  • 2016-10-21T08:46CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_TT201103, PRD, sort_relevancy
  • clientName_golfworks

Can this shaft be used for a putter?

Asked by: Ken
Yes the Command Iron shaft could be used in a putter that uses a .370" tip diameter shaft. The general rule we always followed with using an iron shaft in a putter was to follow the trip trimming instruction for the 9 iron. You could follow either the R flex (IR2) or the S flex (IR5) depending on how stiff you want the shaft to play.
Answered by: JimY
Date published: 2016-10-03

I purchased a 3 iron taylormade burner 1.0 club head only to go with my set that didn't come with a 3 iron. The existing shafts are factory Taylormade super fast  stiff shafts. I'm looking for a new shaft for the 3 iron club head. Any recommendations. 

Asked by: Dinubilo123
The Superfast Steel was most likely an 85 gram steel shaft. The Burner iron should have a .370 hosel. If you want to maintain a similar feel to the Superfast, you might consider the True Temper XP 95. It is slightly heavier and is a high trajectory shaft. Without knowing exactly what your looking for in trajectory and feel, and not knowing what your swing speed is, it is difficult to make a specific recommendation.
Answered by: GW2002
Date published: 2016-04-15

What does the designation R/S Flex mean?

Asked by: Butch
R/S means it is a combination flex shaft that can be trimmed for either an R flex or an S flex by following the recommended trimming instructions for each flex.
Answered by: JimY
Date published: 2016-02-26

A grip that is .58 on a shaft that is .60 versus a grip that is .60 on a shaft that is .60--- what will be the difference?

Asked by: Nadine
Since the .580" grip will have to stretch to fit over the .600" shaft it will actually oversize the grip by 1/64".
Answered by: Mike Comer
Date published: 2014-12-08

What does r/s mean? Regular to stiff?

Asked by: Butch
  • 2016-10-21T08:51CST
  • bvseo_cps, prod_bvqa, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_5
  • loc_en_US, sid_TT201103, PRD, sort_recentAnswersFirst
  • clientName_golfworks